Omron DST1 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 114

Omron DST1 Series Скачать руководство пользователя страница 29

1-3 Functions

1-3 Functions

1-3-1

DST1-series Safety I/O Terminals

Item Description

Self-diagnosis
functions

Self-diagnosis is performed when power is turned ON and periodically during
operation. When an error occurs, it is treated as a fatal error, the MS indicator will
light in red, and all safety outputs and output data to the network will turn OFF.

Access Control by
Password

After configuration data has been downloaded and verified, configuration data within
the DST1-series Safety I/O Terminals can be protected by a password.

Automatic baud rate
detection

The DST1-series Safety I/O Terminals is automatically set to the baud rate of the
network.

Safety Inputs

The ON/OFF status of each safety
input terminal

DST1

Æ

DeviceNet Master
Safety Master

Safety Outputs

The ON/OFF status of each safety
output terminal

Safety Master

Æ

DST1

I/O data for
control

Standard
Outputs

The ON/OFF status of each test
output terminal (T0 to T3)

DeviceNet Master
or Safety
Master

Æ

DST1

Output
monitors

Safety Output
Monitors

The actual ON/OFF status of each
safety output

Individual Safety
Input Status

Normal flag for each safety input

Combined Safety
Input Status

Common normal flag that is ON
when the all safety inputs are normal

Individual Safety
Output Status

Normal flag for each safety output

Combined Safety
Output Status

Common normal flag that is ON
when the all safety outputs are
normal

Individual Test
Output Status

Normal flag for each test output

Status data

Muting Lamp
Status

Normal flag for test output for
terminal T3 when set as muting
output

DST1

Æ

DeviceNet Master
Safety Master

Contents of remote
I/O communications

General
status data

Indicates the general status of the DST1-series Safety
I/O Terminals by using the following 8 flags.
Bit 0: Safety Input Power Status Flag
Bit 1: Safety Output Power Status Flag
Bit 2: Network Power Voltage Drop Flag
Bit 3: Unit Maintenance Flag
Bit 4: (Reserved)
Bit 5: Combined I/O Port Status Flag
Bit 6: Operation Time Exceeded Flag
Bit 7: Connected Component Maintenance Flag

DST1

Æ

DeviceNet Master

Safety I/O

4 (Single-cast and Multi-cast) (See note.)

No. of connections

Standard I/O 2 (Poll, Bit-Strobe, COS, and Cyclic)

IMPORTANT

Communications with up to 15 Safety Controllers for each connection can
be performed using multi-cast connection. If four connections are used,
however, only a maximum of 30 Safety Controllers total can communicate
with the DST1-series Safety I/O Terminals.

1-6

«
...
27
28
29
30
31
...
»

Содержание DST1 Series



















































































































Отзывы:

Нет отзывов