manualshive.com logo in svg

Omron DST1 Series, Руководство по эксплуатации, Страница: 19 / 114

Поделиться
Скачать
Omron DST1 Series Скачать руководство пользователя страница 19

Glossary

 

Glossary 

 

Term Description 

idle data 

Data sent when the originating application is in an inexecutable state.   

assembly 

Internal data in a device gathered as one group to be accessed externally.   

safety data 

Data with high reliability. 

error latch time 

The time period to hold an error state (control data, status data, and LED 
indications). 

open type 

The open method for Safety Connection. One of three types is selected in the 
settings of a connection to the Safety Master. 

connection 

A logical communications path used to communicate between devices.   

configuration 

The settings for a device and a network.   

single channel 

Using only one input or output as the input or output. 

standard 

A device or device function to which safety measures are not applied. 

safety controller (safety PLC) 

A controller with high reliability used for the safety control.   

safety chain 

The logical chain to actualize a safety function, that consists of the input device 
(sensor), the control device (including a remote I/O device), and the output 
device (actuator). 

safety protocol 

The communications hierarchy added to actualize highly reliable 
communications. 

safety signature 

A certificate of the configuration data issued to a device from the Network 
Configurator. The device verifies that the configuration data is correct by using 
the safety signature.   

test pulse 

A signal used to detect external wiring coming into contact with the power supply 
(positive) or short circuits between signal lines.   

dual channel 

Using two inputs or outputs as the input or output for redundancy.   

Dual Channel Complementary 

Setting to evaluate that two logic states are complementary. 

Dual Channel Equivalent 

Setting to evaluate that two logic states are equivalent.   

Busoff 

Status that occurs when the error rate is extremely high over a communications 
cable. An error is detected when the internal error counter exceeds a certain 
threshold value. (The internal error counter is cleared when the Master is started 
or restarted.)   

DeviceNet Safety 

A safety network that adds a safety protocol to DeviceNet to comply with 
IEC61508 SIL3, EN954-1 Safety Category 4. 

discrepancy time 

The time period from a change in one of two inputs until the other input changes. 

EPI 

The interval of safety data communications between the Safety Master and the 
Safety Slave.   

multi-cast connection 

Safety I/O communications in a 1:n configuration (n = 1 top 15). 

single-cast connection 

Safety I/O communications in 1:1 configuration . 

TUNID 

The UNID of the local node. Usually the TUNID is set from the Network 
Configurator.  

UNID 

A identifier to specify one device in all the network domains. Values combining 
the network address and the node address are used.   

 

 

13 

Содержание DST1 Series



















































































































Отзывы:

Нет отзывов