Olympus AL120-6 Series Скачать руководство пользователя страница 70

Страница: 70 / 80

Troubles and Countermeasures

/ When Error Codes Are Displayed

Operation Manual

5-4

Page

Error Codes

Error No.

Error details

Remarks

A Vertical movement errors

E0101

A Vertical No sensor detection after movement to the upper point

U204

E0102

A Vertical No sensor detection after movement to the middle point

U205

E0103

A Vertical No sensor detection after movement to the lower point

U206

E0105

A Vertical Two or more sensors ON

U204,U205,U206

E0106

A Vertical Not in place at the start of operation

E0107

A Vertical Movement set to an impossible position

E0108

A Vertical No initialization within the specified time

U206

E0111

A Vertical Not in a position where it can be initialized

E0112

A Vertical Driver origin signal cannot be detected

E0113

A Vertical Overheating of motor driver

A Horizontal movement errors

E0201

A Linear

No sensor detection after movement to the macro
position

U203

E0202

A Linear

No sensor detection after movement to the position
before the cassette

U202

E0203

A Linear

No sensor detection after movement to the cassette
position

U201

E0205

A Linear

Two or more sensors ON

U201,U202,U203

E0206

A Linear

Not in place at the start of operation

E0207

A Linear

Movement set to an impossible position

E0208

A Linear

No initialization within the specified time

U203

E0211

A Linear

Not in a position where it can be initialized

E0212

A Linear Driver origin signal cannot be detected

E0213

A Linear Overheating of motor driver

A Rotary movement errors

E0301

A Rotation No sensor detection after movement to the home

position

U207

E0302

A Rotation No sensor detection after movement to Side 1

U208

E0303

A Rotation No sensor detection after movement to Side 2

U209

E0305

A Rotation Two or more sensors ON

U207,U208,U209

E0306

A Rotation Not in place at the start of operation

E0307

A Rotation Movement set to an impossible position

E0308

A Rotation No initialization within the specified time

U207

E0309

A Rotation Arm tilt sensor cannot be detected

U303

E0310

A Rotation Arm tilt sensor cannot be detected

U304

E0311

A Rotation Not in a position where it can be initialized

E0312

A Rotation Driver origin signal cannot be detected

Содержание AL120-6 Series

















































































Результаты поиска

Содержание AL120-6 Series

Отзывы:

Olympus AL120-6 Series, Руководство по эксплуатации, Страница: 70 / 80

Результаты поиска

Содержание AL120-6 Series

Отзывы: