Olympus AL120-6 Series Скачать руководство пользователя страница 6

Страница: 6 / 80

Introduction

/Safety Precautions

Operation/Maintenance Manual

i-4

Page

15. To get the best performance from this loader, make sure that there is at least the

space shown below (with dimensions in ) around the loader during assembly

and installation.



The dimensions indicated by the dot-dot-dash lines show the stage's movable range.



You can get more working space during maintenance or other work by changing the

observation tube mounting direction and moving the stage.



This installation space is determined according to the SEMI guideline (SEMI

S8-0308). Provide adequate space for operating the loader according to your intended

use by referring to the installation space and outer dimensions shown on the next

page.

Installation space

AL120-6 Series

Unit: mm

Stage movable range

Working space

AL120-86 Series

Unit: mm

Stage movable range

Working space

Содержание AL120-6 Series

















































































Результаты поиска

Содержание AL120-6 Series

Отзывы:

Olympus AL120-6 Series, Руководство по эксплуатации, Страница: 6 / 80

Результаты поиска

Содержание AL120-6 Series

Отзывы: