Olympus AL120-6 Series Скачать руководство пользователя страница 28

Страница: 28 / 80

Outline of Operation Procedure

Operation Manual

2-2

Operation Flow

Controls/Units Reference

page section

Turn the main switch ON Main

switch

2-3

Page

Set a cassette in place on the cassette table

Cassette guide and cassette setting 2-3

---- Select the type of inspection wafer

4-way button

2-3

---- Set the sequence (type of inspection) [Observation]

setup

buttons

2-4

---- Set the inspection mode (All or Sampling)

Inspection mode button

2-4

----

Set the orientation flat and

notch positions on the microscope

[Wafer alignment] position control

2-6

---- Set the inspection time [Inspection

Time]

control

2-7

* for the LMB model only

----

Set the wafer rotation direction

during Top Macro inspection

[Top macro spin direction] control

2-7

* for the LMB model only

----

Set the wafer rotation speed
during Top Macro inspection

[Top macro spin speed] control

2-7

* for the LMB model only

Press the Start button

[Start] button

2-9

Start transfer

Top Macro inspection

Back Macro inspection

2nd Back Macro inspection

-------- Set the vacuum stage in place

Transfer of wafer onto the vacuum stage

2-11 5

Microscope inspection

* For the LMB model only, the [Back Macro Tilt Angle] setting can be changed.

* For the LMB model only, [Top macro spin direction] and [Top macro spin speed] settings can be changed.

* For the LMB model only, the [Back Macro Tilt Angle] setting can be changed.

Temporarily register the inspection results

[Registration] setup buttons

2-12

Stop transfer

[Pause] button

2-13

[Registration] setup buttons

2-13

[Unload]

button

2-14

[Loader

Stop]

button

2-14

[Quit]

button

2-14

Содержание AL120-6 Series

















































































Результаты поиска

Содержание AL120-6 Series

Отзывы:

Olympus AL120-6 Series, Руководство по эксплуатации, Страница: 28 / 80

Результаты поиска

Содержание AL120-6 Series

Отзывы: