Olympus AL120-6 Series Скачать руководство пользователя страница 31

Страница: 31 / 80

Operation Manual

Outline of Operation Procedure

2-5

4 Setting the Sequence (Inspection Type: [Observation] Button

* This function is available for the LMB model only.

The [Observation] setting buttons are used to specify an inspection

sequence.

Specify the inspection sequence before initiating inspection. The

selected sequence cannot be changed once inspection is started.

The LEDs in the selected [Observation] setting buttons light up.

2nd Back Macro

Back Macro

The 2nd Back Macro inspection performs the Back Macro inspection

again with the wafer rotated about 20 degrees counterclockwise on

the macro table after the Back Macro inspection is completed. The

2nd Back Macro inspection enables inspection of the areas hidden by

the rear arm during the Back Macro inspection.

The 2nd Back Macro inspection can be selected only when the

Back Macro inspection is selected.

Ref.

Page

Содержание AL120-6 Series

















































































Результаты поиска

Содержание AL120-6 Series

Отзывы:

Olympus AL120-6 Series, Руководство по эксплуатации, Страница: 31 / 80

Результаты поиска

Содержание AL120-6 Series

Отзывы: