Olympus AL120-6 Series Скачать руководство пользователя страница 14

Страница: 14 / 80

Introduction

/Daily Check

Operation/Maintenance Manual

i-12

Page

AL120-LMB8-90

ALL

set the cassette

No |Size  |Thick

|Comment

1.  |200  |750-400    |

Recall      Wafer      Setting    Memory

5. Daily Check

1. Confirm the following points before operating the loader.

(1) Vacuum supply pressure: -67KPa to -80KPa

When there are not a vacuum gauge and a regulator, please contact it to the OLYMPUS distributor.

(2) Make sure that there are no wafers or tools inside the wafer loader

2. Confirm the following points before starting the inspection.

(1) Make sure that the power is on (Check the liquid crystal panel)

Turn the main switch ON and make sure that each arm position is

initialized and the model name is shown on the liquid crystal panel.

The loader may have been set to skip initialization when the power

is turned on. This is not a malfunction. The loader executes

initialization when the [Start] button is pressed.

(2) Check the loader stop button

Press the loader stop button and make sure that the loader stops operation.

Содержание AL120-6 Series

















































































Результаты поиска

Содержание AL120-6 Series

Отзывы:

Olympus AL120-6 Series, Руководство по эксплуатации, Страница: 14 / 80

Результаты поиска

Содержание AL120-6 Series

Отзывы: