Olympus AL120-6 Series Скачать руководство пользователя страница 4

Страница: 4 / 80

Introduction

/Precautions

Operation/Maintenance Manual

i-2

Page

The AL120 series consists of a wafer loader, a vacuum stage, and other products.

This manual does not cover custom-order specifications or microscopes.

To acquire a comprehensive understanding of both your loader and microscope, please refer to your

microscope operation manual.

You must prepare yourself the table on which the loader is to be installed and the cassettes and wafers to be

inspected and loaded by the loader.

This loader is designed to maximize its operability when it is installed on a table with a height of 700 mm.

The operability is designed based on the SEMI Standard S8.

Our company’s designed operability is not guaranteed if the loader is installed on a table that does not satisfy

the conditions specified above.

Please refer to the SEMI Standard S8 to select a table.

1. Precautions

Operators must follow the instructions in the Operation/Maintenance Manual. If these instructions are not

followed, safety can not be assured, and malfunctions may occur.

The following 3 types of symbols are used in this Manual to draw operators' attention.

: Indicates critical advice in order to protect operators from injury as well as to protect the

loader (including its peripherals) from damage.

: Indicates a cautionary advice to protect the loader from damage.

: Indicates useful information for operation.

Ref.

Caution

Содержание AL120-6 Series

















































































Результаты поиска

Содержание AL120-6 Series

Отзывы:

Olympus AL120-6 Series, Руководство по эксплуатации, Страница: 4 / 80

Результаты поиска

Содержание AL120-6 Series

Отзывы: