manualshive.com logo in svg

OHAUS T72XW AM, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS T72XW AM Скачать руководство пользователя страница 16

EN 8 

7000 SERIES INDICATORS 

 

 

Analog Load Cell Connections 

 WARNING! 

TO AVOID DAMAGE TO THE PCB OR LOAD CELL, REMOVE POWER FROM THE 
T72XW INDICATOR AND WAIT AT LEAST 30 SECONDS BEFORE CONNECTING 
OR DISCONNECTING ANY HARNESS.

 

Load cell connections are made to the load cell connector located on the main board as shown in Figure 1-5.  

The T72XW indicator is designed to power up to ten 350-ohm load cells (or a minimum resistance of approximately 
35 ohms). To confirm that the load cell load for this installation is within limits, the total scale resistance (TSR) must 
be calculated. To calculate TSR: 

TSR = 

Load Cell Input Resistance (Ohms) 

Number of Load Cells 

Ensure that the TSR of the load cell network to be connected to the T72XW has a resistance greater than the 
minimums listed above before connecting the load cells. If the resistance is below the minimum, the T72XW will not 
operate properly. 

In addition, the maximum cable distance must be reviewed. Table 1-4 provides recommended maximum cable 
lengths based on TSR and cable gauge.

 

Table 1-4: Recommended Maximum Cable Lengths 

TSR (Ohms) 

24 Gauge 

(meters/feet) 

20 Gauge 

(meters/feet) 

16 Gauge 

(meters/feet) 

350 

243/800 

610/2000 

1219/4000 

87 (4-350 

 cells) 

60/200 

182/600 

304/1000 

43 (8-350 

 cells) 

30/100 

91/300 

152/500 

35 (10-350 

 cells) 

24/80 

60/200 

120/400 

 

The T72XW indicator is designed to support both 2mV/V and 3mV/V load cells from the same circuitry. A load cell 
output rating selection jumper is not required.  

Figure 1-6 shows the indicator definitions for the analog load cell indicator strip. Note that when using four-wire load 
cells, jumpers must be placed between the +Excitation and +Sense indicators and between the 

Excitation and 

Sense indicators.

 

 

 

Figure 1-6: Load Cell Termination 

Note:

 For the standard four-wire cable: If an increase in load results in a decrease in weight display, reverse the 

signal wires (+SIG and 

SIG). 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды