manualshive.com logo in svg

OHAUS T72XW AM, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS T72XW AM Скачать руководство пользователя страница 11

7000 SERIES INDICATORS 

EN 3 

 

 
 

Table 1-3: T72XW Power Consumption 

 

Input Voltage 

I (mA) 

P (W) 

5V/50 Hz 

167 

7.9 

110 V/50 Hz 

133 

7.7 

240 V/50 Hz 

64 

7.9 

264 V/50 Hz 

59 

7.9 

85 V/60 Hz 

163 

7.9 

110 V/60 Hz 

128 

7.7 

240 V/60 Hz  

62 

7.9 

264 V/60 Hz  

58 

8.0 

 

Values shown are with internal Ethernet option installed and load cell input loaded with 8 x 350

 load cells. 

1.4  Definition of Signal Warnings and Symbols 

Safety notes are marked with signal words and warning symbols. These show safety issues and warnings. Ignoring 
the safety notes may lead to personal injury, damage to the instrument, malfunctions and false results. 
 
Signal Words   
 
           WARNING         for a hazardous situation with medium risk, possibly resulting in injuries or death if not  
                                     avoided.  

CAUTION 

for a hazardous situation with low risk, resulting in damage to the device or  

 

the property or in loss of data, or injuries if not avoided. 

Attention            for important information about the product 
Note 

for useful information about the product 

 
 

 

 

 

Warning Symbols   
   
 

 

 

General Hazard                                                     Electrical Shock Hazard 

 

1.5  Safety Precautions 

 

 

Verify that the input voltage range printed on the data label and the plug type matches the local AC power  
to be used. 

 

Only connect models supplied with a grounded power cord to a compatible grounded power receptacle. 

 

Do not position the indicator such that it is difficult to disconnect the power cord from the power receptacle. 

 

Make sure that the power cord does not pose a potential obstacle or tripping hazard. 

 

Use only approved accessories and peripherals. 

 

Operate the equipment only under ambient conditions specified in these instructions. 

 

Disconnect the equipment from the power supply when cleaning. 

 

Do not operate the equipment in hazardous or unstable environments. 

 

Service should only be performed by authorized personnel. 

 

 

 

Caution:

  Read all safety warnings before installing, making connections, or servicing this equipment. 

Failure to comply with these warnings could result in personal injury and/or property damage. Retain all 
instructions for future reference. 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды