OHAUS T72XW AM Скачать руководство пользователя страница 136

Страница: 136 / 143

EN 128

7000 SERIES INDICATORS

Index

Name

Description

472

COM2 Data Bits

[Refer to values for

445

]

473

COM2 Parity

[Refer to values for

446

]

474

COM2 Flow Control

[Refer to values for

447

]

475

COM2 Interface

– RS232

– RS485

476

COM2 Address

Manual entry

477

Ethernet DHCP Client

– Disabled

– Enabled

478

Ethernet IP address

Manual entry

479

Ethernet Subnet Mask

Manual entry

480

Ethernet gateway

Manual entry

481

Print Client Server IP Address

Manual entry

482

Print Client Server TCP Port

Manual entry

Setup

– Maintenance (read only)

Index

Name

Description

501

Weighment Counter

502

Scale Overloads Counter

503

Not usable

504

Zero Commands Counter

505

Zero Command Failure Counter

Calibration Values (read and write)

Index

Name

Description

601

Zero Counts

Zero counts

602

Mid Test Load

Test weight for mid-point span when
linearity is enabled.

603

Mid Test Load Counts

Test load counts for mid-point span
when linearity is enabled.

604

Span Test Load

Test weight value for high span point.

605

Span Test Load Counts

Test load counts for high span point.

Target Values (read and write)

Index

Name

Description

610

Target Block

Entire set of Target Values

611

Target

Target value

612

-Tol

-Tolerance value

613

+Tol

+Tolerance value

614

Description

Target description

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Результаты поиска

Содержание T72XW AM

Отзывы:

Бренды по названию

Популярные бренды

OHAUS T72XW AM, Инструкция по эксплуатации

Результаты поиска

Содержание T72XW AM

Отзывы:

Бренды по названию

Популярные бренды