manualshive.com logo in svg

OHAUS T72XW AM, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS T72XW AM Скачать руководство пользователя страница 123

7000 SERIES INDICATORS 

EN 115 

 

 

Z 

– ZERO 

Command:  

Z 

Response: 

Z_A 

Command performed, meaning the scale was in gross mode, scale was stable and weight 
was within the zero capture range. 

Response: 

Z_I 

Command understood, not executable at present. 

Response: 

Z_+ 

Upper limit of zero setting range exceeded. 

Response: 

Z_-  

Lower limit of zero setting range exceeded. 

 

 

Comments 

The calibrated zero point determined during calibration is not influenced by this command. 
The indicator 

will wait for up to 3 seconds after receiving an “Z” command for no-motion. If motion does not settle 

within this time, the command is aborted and the Z_I response is sent. 
 

@ 

– RESET 

Command:  

@ 

 

Response: 

I4_A_“12345678” 

12345678 

Serial number of the scale 

 

Comments 

Resets the scale to the condition found after switching on, but without a zero setting being performed. 
All commands awaiting responses are canceled. 
The tare register is cleared. 
The SIR and SR commands are cancelled. 
The Reset command is always executed except that a Reset command received by the indicator during the 
calibration and test procedure cannot be processed. 
 

Commands and Responses MT-SICS Level 1 

The following commands of MT-SICS level 1 are available: 

SR 

Send weight value on weight change (Send and Repeat) 

T 

Tare 

TA 

Set or inquiry of preset tare value 

TAC 

Clear tare value 

TI 

Tare Immediately 

SR 

– SEND WEIGHT VALUE ON WEIGHT CHANGE (SEND AND REPEAT) 

Command:  

SR_Value_Unit 

 

SR 

Response:  

S_S_ _ _ _ _ 105.1_lb  Current stable weight. 

 

 

S_D_ _ _ _ _ 106.7_lb  Dynamic weight value. 
S_S_ _ _ _ _ 124.3_lb  Next stable weight value. 

Response: 

S_I 

Command understood, not executable at present. 

Response: 

S_L 

Command understood, invalid parameter. 

Response: 

S_+ 

Indicator in overload range. 

Response: 

S_- 

Indicator in underload range. 

 

Example 
Command:  

SR_0.50_kg 

Send the current stable weight value followed by every load change > 0.50 kg. 

Response: 

S_S_ _ _ _ _100.00_kg  

Scale stable. 

S_D_ _ _ _ _115.23_kg  

More than 0.50 kg loaded. 

S_S_ _ _ _ _200.00_kg  

Scale stable again. 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды