NEC N8100-1220F Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 494

background image

3-6 Setting Up Your Server

Installing or Removing the Server into/from the Rack

This subsection provides the instructions for the rack-mount server unit into a standard EIA 19-inch
rack cabinet.

This subsection also describes the removal procedures for the rack mount server unit from the 19-
inch rack cabinet.

WARNING

Observe the following instructions to use the server safely. Failure to follow
these instructions may result in death or serious personal injury. See pages
1-3 to 1-8 for details.

■

Do not use any rack which does not conform to the relevant standard.

■

Disconnect the power cord(s) before installing or removing the server.

CAUTION

Observe the following instructions to use the server safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage.
See pages 1-3 to 1-8 for details.

■

Do not leave more than one device being pulled out from the rack.

■

Do not lift the server only by a single person.

■

Always install the server in the specified place.

■

Do not install the server on the rack leaving the cover removed.

■

Do not pinch your finger with mechanical components.

«
...
80
81
82
83
84
...
»

Содержание N8100-1220F















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для N8100-1220F

Бренд: IBM Страницы: 88

Бренд: Xerox Страницы: 8

Бренд: Cobalt Digital Inc Страницы: 218

Бренд: Lantech Страницы: 49

Бренд: Velvac Страницы: 55

DiskStation Series

Бренд: Synology Страницы: 6

Бренд: Cisco Страницы: 23

Бренд: Cisco Страницы: 75

Бренд: Cisco Страницы: 132

Бренд: Cisco Страницы: 58

UCS 6400 Series

Бренд: Cisco Страницы: 68

Smart Storage NSS322

Бренд: Cisco Страницы: 2

HAM RADIO DELUXE

Бренд: Kenwood Страницы: 16

Бренд: Polycom Страницы: 11

Бренд: Lightwave Communications Страницы: 97

Бренд: Avaya Страницы: 270

Бренд: Kramer Страницы: 2

Бренд: ClearCube Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды