NEC N8100-1220F Скачать руководство пользователя страница 428

Страница: 428 / 494

9-54 Upgrading Your Server

Unlock the memory board to open the ejector.

IMPORTANT:

The memory board becomes very hot while being

powered. When removing the board, turn off the power and wait for
several minutes before pulling it out.

Note that the hot-plug memory board is off-powered when it is
unlocked (the LED goes off). Wait several minutes in this state.

Hold the ejector and pull the memory board out from the server.

Put the memory board on a dry, clean, and static-free place.

Installation

Install the memory board in reverse order of the removal steps.

Содержание N8100-1220F















































































































































































































































































































































































































































































































Результаты поиска

Содержание N8100-1220F

Отзывы:

Похожие инструкции для N8100-1220F

Бренды по названию

Популярные бренды

NEC N8100-1220F, Руководство пользователя

Результаты поиска

Содержание N8100-1220F

Отзывы:

Похожие инструкции для N8100-1220F

Бренды по названию

Популярные бренды