Motorola SC 300 Скачать руководство пользователя страница 85

Страница: 85 / 188

Overview

DEC 2000

3-1

300 BTS Hardware Installation, ATP and FRU Procedures

PRELIMINARY

Overview

This chapter provides the information and procedures to:

Unpack the equipment and inspect for damage.

Install rack, pole or ceiling adapters.

Install the mounting bracket on a wall, pole, rack or ceiling.

Attach the unit and covers to the mounting bracket.

Procedure order

The process of installing the mounting bracket and Remote GPS receiver
requires that the following procedures be completed in the order shown.

1. Unpack the equipment and inspect for damage.

2. Install the mounting hardware on a wall, rack, pole or ceiling.

3. Attach the back solar cover.

4. Install the Remote GPS head.

Содержание SC 300





























































































































































































Результаты поиска

Содержание SC 300

Отзывы:

Похожие инструкции для SC 300

Бренды по названию

Популярные бренды

Motorola SC 300, Руководство пользователя

Результаты поиска

Содержание SC 300

Отзывы:

Похожие инструкции для SC 300

Бренды по названию

Популярные бренды