Motorola SC 300 Скачать руководство пользователя страница 103

Страница: 103 / 188

Attaching Back Solar Cover to Mounting Bracket

DEC 2000

3-19

300 BTS Hardware Installation, ATP and FRU Procedures

PRELIMINARY

Objective

The objective of this procedure is to attach the back solar cover to the
mounting bracket.

When to Use the Cover

Solar Covers are required in all outdoor applications

Required tools

The following tools are required to attach the back solar cover to the
mounting bracket.

Torque driver wrench, 1/4–in. hex female drive, 0–10 N–M

T30 Torx bit

Procedure

Attach the back solar cover to the mounting bracket by following the
procedure in Table 3-10 and the information in Figure 3-8.

Table 3-10: Procedure to attach Back Solar Cover to Mounting

Bracket

Step

Action

Place the back solar cover on the mounting bracket so the
cooling vents are at the top. Align the four M6 screws with
the mounting holes.

Using a T30 Torx bit, start but do not tighten all four M6
screws.

Using the T30 Torx bit, tighten the four M6 screws to 5.0
N–m.

Содержание SC 300





























































































































































































Результаты поиска

Содержание SC 300

Отзывы:

Похожие инструкции для SC 300

Бренды по названию

Популярные бренды

Motorola SC 300, Руководство пользователя

Результаты поиска

Содержание SC 300

Отзывы:

Похожие инструкции для SC 300

Бренды по названию

Популярные бренды