Motorola SC 300 Скачать руководство пользователя страница 167

Страница: 167 / 188

Antenna Cabling for Sites Equipped With Optional Primary Surge
Suppressor

– continued

DEC 2000

5-19

300 BTS Hardware Installation, ATP and FRU Procedures

PRELIMINARY

Procedure to Install Antenna
Cabling for Sites Equipped
with Primary Surge Suppressor

Do the procedure in Table 5-11 to install the antenna cabling.

Lightning arrestors are installed on the Primary Surge
Suppressor for two units. You must add additional
lightning arrestors when you expand from one to two units;
two to three units and from three to four units.

IMPORTANT

Table 5-11: Procedure to Install Antenna Cabling for Sites Equipped

with Primary Surge Suppressor

Step

Action

Route cable D (antenna cable) between the unit(s) and the
Primary Surge Suppressor.

Route cable C (antenna cable) from the Primary Surge
Suppressor directly to the antenna(s).

Torque connectors to 4.3 N–m.

Figure 5-14: Antenna Cabling for one Microcell with Primary Surge Suppressor

MICROCELL 1

KEY

B/1(ANTENNA)

LABEL

NUMBER

OF CABLES

NAME

D/1(ANTENNA)

PRIMARY SURGE
SUPPRESSOR

ANT A

ANT B
TX/RX

D/1(ANTENNA)

C/1(ANTENNA)

Содержание SC 300





























































































































































































Результаты поиска

Содержание SC 300

Отзывы:

Похожие инструкции для SC 300

Бренды по названию

Популярные бренды

Motorola SC 300, Руководство пользователя

Результаты поиска

Содержание SC 300

Отзывы:

Похожие инструкции для SC 300

Бренды по названию

Популярные бренды