manualshive.com logo in svg

Motorola DSP56303, Руководство пользователя

DSP56303 - мощный процессор от Motorola, предназначенный для обработки сигналов. Обеспечивает высокую производительность и отличное качество звука. Для полноценного использования устройства необходимо ознакомиться с инструкцией по эксплуатации. Скачайте бесплатное руководство пользователя с manualshive.com.

Поделиться
Скачать
background image

Operation

7

-8

DSP56303 User’s Manual

n

ESSI receive last slot interrupt:
Occurs when the ESSI is in Network mode and the last slot of the frame has ended. 
This interrupt is generated regardless of the receive mask register setting. The receive 
last slot interrupt can signal that the receive mask slot register can be reset, the DMA 
channels can be reconfigured, and data memory pointers can be reassigned. Using the 
receive last slot interrupt guarantees that the previous frame is serviced with the 
previous setting and the new frame is serviced with the new setting without 
synchronization problems. 

Note:

The maximum time it takes to service a receive last slot interrupt should not exceed 
N – 1 ESSI bits service time (where N is the number of bits the ESSI can transmit 
per time slot).

n

ESSI transmit data with exception status:
Occurs when the transmit exception interrupt is enabled, at least one transmit data 
register of the enabled transmitters is empty, and a transmitter underrun error has 
occurred. This exception sets the SSISR[TUE] bit. The TUE bit is cleared when you 
first read the SSISR and then write to all the transmit data registers of the enabled 
transmitters, or when you write to TSR to clear the pending interrupt.

n

ESSI transmit last slot interrupt:
Occurs when the ESSI is in Network mode at the start of the last slot of the frame. This 
exception occurs regardless of the transmit mask register setting. The transmit last slot 
interrupt can signal that the transmit mask slot register can be reset, the DMA channels 
can be reconfigured, and data memory pointers can be reassigned. Using the Transmit 
Last Slot interrupt guarantees that the previous frame is serviced with the previous 
frame settings and the new frame is serviced with the new frame settings without 
synchronization problems.

Note:

The maximum transmit last slot interrupt service time should not exceed 
N – 1 ESSI bits service time (where N is the number of bits in a slot).

n

ESSI transmit data:
Occurs when the transmit interrupt is enabled, at least one of the enabled transmit data 
registers is empty, and no transmitter error conditions exist. Write to all the enabled 
TX registers or to the TSR to clear this interrupt. This error-free interrupt uses a fast 
interrupt service routine for minimum overhead (if no more than two transmitters are 
used).

Содержание DSP56303

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSP56303

Wilfa MC3B-400S Operating Instructions Manual preview
MC3B-400S
Бренд: Wilfa Страницы: 54
Altec Lansing 4048A SIGNAL PROCESSING Specifications preview
4048A SIGNAL PROCESSING
Бренд: Altec Lansing Страницы: 2
Hamilton Beach 840088000 Manual preview
840088000
Бренд: Hamilton Beach Страницы: 12
Rotel RDP 980 Owner'S Manual preview
RDP 980
Бренд: Rotel Страницы: 7
Rotel Digital Audio Processor RDP 980 Owner'S Manual preview
Digital Audio Processor RDP 980
Бренд: Rotel Страницы: 7
Ovente PF1007 Series Manual preview
PF1007 Series
Бренд: Ovente Страницы: 12
I TUTTOFARE YUP000001 Instruction Manual preview
YUP000001
Бренд: I TUTTOFARE Страницы: 44
Brentwood Appliances MS-101 Operating And Safety Instructions Manual preview
MS-101
Бренд: Brentwood Appliances Страницы: 12
M-system W5DY Instruction Manual preview
W5DY
Бренд: M-system Страницы: 5
Audison bit One HD Virtuoso User Manual preview
bit One HD Virtuoso
Бренд: Audison Страницы: 90
Glen GL 4043 User Manual preview
GL 4043
Бренд: Glen Страницы: 2
Kunft KMC3833 Instruction Manual preview
KMC3833
Бренд: Kunft Страницы: 23
Kompernass 339545 1910 Operating Instructions Manual preview
339545 1910
Бренд: Kompernass Страницы: 74
Braun Multipractic UK 95 Use Instructions preview
Multipractic UK 95
Бренд: Braun Страницы: 9
Braun MQ 40 Manual preview
MQ 40
Бренд: Braun Страницы: 39
Orban OPTIMOD-AM 9300 Operating Manual preview
OPTIMOD-AM 9300
Бренд: Orban Страницы: 242
WEISS DSP501 User Manual preview
DSP501
Бренд: WEISS Страницы: 38
Westinghouse WST2025ZE Owner'S Manual preview
WST2025ZE
Бренд: Westinghouse Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды