manualshive.com logo in svg

Motorola DSP56303, Руководство пользователя

Поделиться
Скачать
Motorola DSP56303 Скачать руководство пользователя страница 134

DSP Core Programming Model

6

-20

DSP56303 User’s Manual

5

HAEN

0

Host Acknowledge Enable 
Controls the HACK signal. In the single host request mode (HDRQ is 
cleared in the ICR), if HAEN and HREN are both set, HACK/HRRQ is 
configured as the host acknowledge (HACK) input. If HAEN or HREN is 
cleared, HACK/HRRQ is configured as a GPIO signal according to the 
value of the HDDR and HDR. In the double host request mode (HDRQ is 
set in the ICR), HAEN is ignored.

4

HREN

0

Host Request Enable
Controls the host request signals. If HREN is set and the HI08 is in the 
single host request mode (that is, if HDRQ is cleared in the host interface 
control register (ICR)), then HREQ/HTRQ is configured as the host 
request (HREQ) output. If HREN is cleared, HREQ/HTRQ and 
HACK/HRRQ are configured as GPIO signals according to the value of 
the HDDR and HDR.

If HREN is set in the double host request mode (that is, if HDRQ is set in 
the ICR), HREQ/HTRQ is configured as the host transmit request (HTRQ) 
output and HACK/HRRQ as the host receive request (HRRQ) output. If 
HREN is cleared, HREQ/HTRQ and HACK/HRRQ are configured as 
GPIO signals according to the value of the HDDR and HDR.

3

HCSEN

0

Host Chip Select Enable
If the HCSEN bit is set, HCS/HA10 is a host chip select (HCS) in the 
non-multiplexed bus mode (that is, when HMUX is cleared) and host 
address line 10 (HA10) in the multiplexed bus mode (that is, when HMUX 
is set). If this bit is cleared, HCS/HA10 is configured as a GPIO signal 
according to the value of the HDDR and HDR.

2

HA9EN

0

Host Address Line 9 Enable
If HA9EN is set and the HI08 is in multiplexed bus mode, then HA9/HA2 is 
host address line 9 (HA9). If this bit is cleared and the HI08 is in 
multiplexed bus mode, then HA9/HA2 is configured as a GPIO signal 
according to the value of the HDDR and HDR.

NOTE: HA9EN is ignored when the HI08 is not in the multiplexed bus 
mode (that is, when HMUX is cleared).

1

HA8EN

0

Host Address Line 8 Enable
If HA8EN is set and the HI08 is in multiplexed bus mode, then HA8/A1 is 
host address line 8 (HA8). If this bit is cleared and the HI08 is in 
multiplexed bus mode, then HA8/HA1 is a GPIO signal according to the 
value of the HDDR and HDR.

NOTE: HA8EN is ignored when the HI08 is not in the multiplexed bus 
mode (that is, when HMUX is cleared).

0

HGEN

0

Host GPIO Port Enable
Enables/disables signals configured as GPIO. If this bit is cleared, signals 
configured as GPIO are disconnected: outputs are high impedance, inputs 
are electrically disconnected. Signals configured as HI08 are not affected 
by the value of HGEN.

Table 6-12. Host Port Control Register (HPCR) Bit Definitions  (Continued)

Bit Number

Bit Name

Reset Value

Description

Содержание DSP56303

































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды