Morita SIGNO G20 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 98

Morita SIGNO G20 Скачать руководство пользователя страница 83

83

O-Ring

Bacteria Filter

Filter Case

[6]Maintenance 11.

(5)Unscrew the filter cases inside the plumbing pit.

The water filter case will be full of water and some water
will drip out of its holder. Hae a cloth ready to wipe up any
water that spills out. Also have a bucket handy.

(6)Pull the old filters off their holders and replace them with new filters.
Make sure the new filters are firmly in place.

Ensure the O-ring is fitting in right way before insert.

(7)Install the new cases onto the holders. Carry the case and turn right
until screw.

Using excessive force or skewing the cases to screw
them on could crack them.

    (8)Check that there is no water or air leakage.
        Open the main valves, turn the unit on and operate the three-way
        syringe.

Make sure the air and water come out normally and
that there is no leakage around the filter cases.

(9)Turn off the main switch and put the cover back on the plumbing pit.

(10)Turn the main switch on and make sure everything works properly.

There may be some air in the water lines right after
replacing the filter. Run the auto filler or something else
until the air in the lines is eliminated.

ADVICE

CHECK

ADVICE

CHECK

ADVICE

«
...
81
82
83
84
85
...
»

Содержание SIGNO G20



































































































Отзывы:

Нет отзывов