Morita SIGNO G20 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 98

Morita SIGNO G20 Скачать руководство пользователя страница 8

8

[4]Preliminary Adjustments and Connections

2. Instrument Connections

Before using the equipment, connect all the main in-
strument tubes. As for the threeway syringe, connect
the syringe body as well as the tube.

(except for the one-

touch detachable WS90,option).
>>Otherwise, air or water could leak out.

All instruments must be in their specified holders ex-
cept when in use.

>>Otherwise, an injury or damage could result from using
the vacuum syringe or some other instrument.

CAUTION

  Connect the main tubes for the doctor’s instruments to their tray and those
  for the assistant to the assistant’s tray.
  Then put all the instruments in their specified holders. Refer to the chart at
  the right and the instructions below.
  Main Tube Connections: The Installation manual.

  >>Three-way Syringe Body and Nozzle Attachment: Section [5] 6. of this
      manual
  >>Vacuum Syringe and Saliva Ejector: Section [5] 5. (7) and (8) of this
      manual
  >>Various Instruments: Individual operator’s manuals for each instrument

3. Install the Filters

  The chart shows the various filters that are required and supplied with the
  equipment.
  Refer to Section [6] Maintenance in this manual for installation instructions.
  For your information, filter specification differs according to your selection of
  optional equipments.

CAUTION

All the filters must be installed before the equipment is
used.

>>If the filters and their covers are not correctly installed, the
    equipment may not perform satisfactorily or could be
    damaged. Also water, air or vacuum lines could become
    blocked.

Filters

1

Vacuum Cut Filter

2

Saliva Ejector Cut Filter

3

Basin Filter

4

Drain Trap Filter

5

Oil Drain Filter

6

Water Bacteria Filter

7

Air Bacteria Filter

«
...
6
7
8
9
10
...
»

Содержание SIGNO G20



































































































Отзывы:

Нет отзывов