Morita SIGNO G20 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 98

Morita SIGNO G20 Скачать руководство пользователя страница 35

35

[5]Operation 6.

2)Operation

Step on the foot pedal to operate the scaler. It vibrates at a steady
rate.
When the spray is turned on, it will be emitted when the foot pedal is
depressed.
There are 10 power levels for each power range. The upper limit for each
range can be set. (See [5]3.(3) below.)
The vibration level is shown in the display. (Refer to level estimates.)

Splay ON (Ultrasonic Scaler)

Pedal Rotaion Splay

Step Hold ON

(9)Ultrasonic Scaler

*

1)Attaching the handpiece

LED without light

Align the notch on the handpiece side with the mark on the
tube side and insert the syringe.

With LED Light

Align the handpiece side mark with the tube side mark and
insert the syringe.

Please connect the handpiece and tube reliably.
It may unexpectedly deviate if it is not securely connected.

LED with out light

With LED light

tube

mark

mark

notch

*:option

Power Level Estimates

Setting

Power Range

PER 0.5(weakest) - 10

(Weak)

END 0.5 - 10

(Medium)

SCL 0.5 - 10(strongest)

(strong)

«
...
33
34
35
36
37
...
»

Содержание SIGNO G20



































































































Отзывы:

Нет отзывов