manualshive.com logo in svg

Morita SIGNO G20, Руководство по эксплуатации, Страница: 39 / 98

Поделиться
Скачать
Morita SIGNO G20 Скачать руководство пользователя страница 39

39

Flushing Lamp

Flushing Switch

  

[5]Operation 7.

 

Flushing  Bowl  Connections

Instrument 

 

   Main Tube Set Up

H.S.

L.S.

SC.

EV.
S.E.

W.S.

Disconnect Hand piece

Disconnect Attachment

Take Tip Off

Take nozzle off

4)Flushing Device 

*

This is used to flush out all the water lines inside the unit.
Do this once a day.
Switch On the main switch and follow the direction in the display.

a)Set the flushing bowl up on the basin. Line up and fit the gauge on
   top of the bowl to the end of the auto filler for correct positioning.

There is a magnet in the bottom of the bowl, and
a sensor detects whether the bowl is correctly
positioned.
When the bowl is in the correct position, the auto
filler stops running.

b)An inside magnet switch detects the flushing device, and then the
   flushing preparation mode boots up automatically.

Once the body detects the flushing device, the
flushing lamp on the assistant’s switch panel lights
up. Seeing the flush lamp light up, you can con-
firm that the flushing device is set up on the basin
properly.

c)Connect the main tubes to the flushing bowl.
   Do not fail to connect the tubes in the order shown in the chart at the
   right and matched to their mates labeled on the bowl.
   Fix the water lever for the threeway syringe so that it is held down.
   There is a device on the bowl to do this.

ADVICE

Flushing Bowl

L.S./H.S.

Micromotor/
Air Turbine Hand pieces

W.S.

Three-way Syringe

　　S.E.

　　Saliva Ejector

SC.

Ultrasonic Scaler

Hole in Bowl
（position under auto filler）

Set Up Gauge
（Position by fitting to

 auto filler）

EV.

Vacuum Syringe

W.S.

Three-way Syringe

CHECK

Содержание SIGNO G20



































































































Отзывы:

Нет отзывов