Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 40 / 68

54D0700

BDV Series Gas Fireplace

OptIONAL FAN BLOWER SyStEM

Figure 53 - Junction Box Wiring Diagram

FP1912
Junction box wiring
8/08

Junction Box

Factory Supplied

Not Supplied

120V AC

60Hz

OPTIONAl FAN/BlOWER SYSTEM (BlOTSC)

Installation Instructions
Wiring

1. Before installing the blower, wire the receptacle into an

electrical circuit. This should be done before framing the

fireplace. Wire with minimum 60° C wire in accordance

with prevailing codes.

2. Remove the external junction box cover by removing the

screw from the left side of the outside firebox wall. Junc-

tion box was installed at the factory.

3. The junction box cover has a factory installed “romex”

style strain relief connector. After connect-

ing the wires, route the wire leads through

this connector. Refer to the wiring diagram in

Figure 53

Before Installing the Blower

1. Always turn off the gas supply and allow the

unit to cool down before proceeding.

2. Clean the inside of the firebox (wall and

floor), where the blower and wires will be in-

stalled. Make sure the firebox wall and floor

are clean and dry before mounting the blow-

er.

Installing the Blower

1. Remove the lower access panel by pulling up

and away from unit.

2. Remove glass frame by releasing the two (2)

latches (500 and 600 models have three (3)

latches) below the firebox opening and lifting

glass frame up and away from unit.

3. Use the supplied Velcro on the blower and the magnetic strips to secure the blower to the

firebox wall and floor.

Figure 54

4. Remove the tape from the back of the Velcro strips, slide the blower through lower access

door and position on the inside back firebox wall. The blower should be centered with the

rear blower discharge vent facing up (pointing up between the inside firebox wall and inner

combustion wall). The blower should be flat against the firebox back wall.

Figure 55

5. For 300 models, the air shield can be removed.

Figure 54

6. Align the connector pin on the AC box to the control box

and gently push them together using the guiding block as a

guide.

Figure 56

KT553
velcro, magnets
12/08

Velcro Strips

Magnets

Air Shield

(Remove from

300 Models)

Discharge

Vent

Fireplace

KT553

top View

Front View

Side View

Figure 54 -

Velcro, Magnet Locations

KT552
fan location
12/08

Figure 55 -

Blower Location

KT552

Keep wires away from

combustion chamber

and blower wheel.

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды