Monessen Hearth Direct Vent Gas Fireplace BDV300 страница 49 Скачать руководство пользователя

Страница: 49 / 68

54D0700

FP1943
pilot flame

Figure 62 - Pilot Flame

Thermopile

Thermocouple

FP1943

BDV Series Gas Fireplace

Turn off gas before servicing fireplace. It is recommended that a qualified service

technician perform these check-ups at the beginning of each heating season

ARNING

BuRNER FLAME

The flames from the burner should be visually

checked as soon as the heater is installed and

periodically during normal operation. In normal

operation, at full rate, and after operating for about

15 to 30 minutes, the flame should be yellow and

slightly taller than the rear log.

Figure 63

If the flame is blue and only in the center, turn off

unit and let cool. After unit is cool, remove logs and

check to make sure the back holes in the burner

are not covered with rock wool. If the back holes

are clear, add more rock wool to the center of the

burner. Replace logs.

NOTE: The type of installation, vent system

configuration, and wind effects may cause the

flame patterns to vary.

cLEANING and MAINtENANcE

BuRNER, pILOt AND cONtROL cOMpARtMENt

Keep the control compartment, logs, and burner areas surrounding the

logs clean by vacuuming or brushing at least twice a year. Make sure

the burner porting, pilot air opening and burner air opening are free of

obstructions at all times.

pILOt FLAME

The flames from the pilot should be visually checked as soon as the

heater is installed and periodically during normal operation.

the pilot

flame must always be present when the fireplace is in operation.

Figure 62

. The pilot flame has three distinct flames, one engulfing the

thermopile, one engulfing the thermocouple, and the other reaching to

the main burner.

BuRNER

Inspect area around the injector. Remove any lint or foreign material

with a brush or vacuum.

LG588
BDV log flame

Figure 63 - Burner Flame Appearance

LG587

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды