Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 24 / 68

54D0700

FP1969
firestop w room above

FP1970
firestop no room

BDV Series Gas Fireplace

VENt INStALLAtION

1. Determine the route your vertical venting will take. If ceiling

joist, roof rafters or other framing will obstruct the venting

system, consider an offset. Refer to

Figure 30

to avoid cut

ting load bearing members.

For optimal flame appearance, a restrictor disk is necessary

on straight vertical runs of 20' of more.

• Runs may not incorporate elbows.
• The disk is part number 45D0551 and is included in

installation manual packet.

• Drop the disk into a 4" inner collar before installing the

first section of flue or install at the last section before

installing the termination.

• An additional disk may be installed on runs of 35' or

more. Rotate disks perpendicular to each other.

NOTE: Pay special attention to these installation instructions

for required clearances (air space) to combustibles when

passing through ceilings, walls, roofs, enclosures, attic

rafters, etc. Do not pack air spaces with insulation. Also

note maximum vertical rise of the venting system and any

maximum horizontal offset limitations. Offsets must fall

within the parameters shows in Figure 13, page 20.

2. Set fireplace in desired location. Drop a line plumb down

from the ceiling to the position of the flue exit. Mark the

center point where the vent will penetrate the ceiling. Drill

a small locating hole a this point.

Drop a plumb line from the inside of the roof to the ceiling

locating hole in the ceiling. Mark the center point where

the vent will penetrate the roof. Drill a small locating hole

at this point.

FLAt cEILING INStALLAtION

1. Cut a 9

" (241 mm) square hole in the ceiling using the

locating hole as a center point The opening should be

framed to 9

" x 9

" (241 mm x 241 mm) inside dimen-

sions as shown in

Figure 32

using framing lumber the same

size as the ceiling joist. If the area above the ceiling is an

insulated ceiling or a room, nail firestop from the top side.

This prevents loose insulation from falling into the required

clearance space.

Figure 31.

Otherwise, install firestop

below the framed hole.

Figure 32

2. Assemble the desired lengths of pipe and elbows necessary

to reach from the burner system flue up through the firestop.

Be sure pipe and elbow connections are fully twist-locked.

Figure 15, page 18

INStALLAtION FOR VERtIcAL tERMINAtION

FP1969
offset w/ wallstrap

FP1669

Figure 30 - Offset with Wall Strap and 45° Elbows

Roof Flashing

Wall Strap

45° Elbows

Ceiling Firstop

Figure 31 - If Area Above is a Room, Install

Firestop above Framed Hole as Shown

Figure 32 - If Area Above is Not a Room, Install

Firestop above Framed Hole as Shown

Firestop

Nails

Firestop

FP1969

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды