Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 48 / 68

54D0700

LG586
BDV logs set

Flat

Area

BDV Series Gas Fireplace

FINAL INStALLAtION

LOG pLAcEMENt

1. Place rear log (#1) on grate assembly. Log should rest

firmly on the two log mounting pins on the bars.

Figure

2. Place top right log (#2) on the rear log. Rest the right

back side of the log in the flat area of the rear log. Place

the narrow front end of the log next to the center vertical

grate bar.

Figure 61

3. Place the top left log (#3) on the rear log. Nest the

forked end of the top left log into the fork or the rear

log. Rest the narrow end of the top left log behind the

center vertical grate bar.

Figure 61

LAVA ROcK AND EMBER pLAcEMENt

Sprinkle lava rock on the floor of the inner combustion

chamber. Evenly distribute the rock. Do not pile the lava rock

up in front of grate. Do not place lava rock on the burner.

If desired, purchase optional embers to decorate the floor

of the fireplace.

Figure 61 - Log Placement

(BDV300, 400 shown)

(#3) Top

Left Log

(#2) Top Right Log

(#1) Rear

Log

Left Vertical

Grate Bar

Right Vertical

Grate Bar

Center Vertical

Grate Bar

Log Mounting

Pins

ROcK WOOL pLAcEMENt

1. Place rock wool on burner to provide glowing

embers. For best results, pull the rock wool

apart into pieces the size of a dime or smaller.

NOtE:

Embers must be loosely placed to allow

proper burner flame.

2. Distribute one layer of rock wool to cover the

burner.

Figure 60

3. Place the logs on the burner. Refer to

Log

Placement

below. Light unit and after 15 min-

utes, check burner flame and glow. Refer to

Burner Flame

, Page 49.

If the flame is blue and only in the center, turn off

unit and let cool. After unit cools, remove logs. If

the back holes are clear, add more rock wool to the

center of the burner. Replace logs and check flame

again. Save left over rock wool to refresh when

cleaning later. Too much rock wool can disturb the

flame and cause sooting on the glass or logs.

Do not sprinkle the lava rock or ember

chunks on top of the burner. This may

cause potential sooting, glass breakage

and a fire hazard.

ARNING

Do not use the entire bag of rock wool

to cover the burner. This could cause

the flame to burn poorly and may lead

to sooting.

ARNING

FP2105
BDV base

Figure 60 - Placement of

Rock Wool on Burner

Cover with

Rock Wool

Burner

FP2105

LG586

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды