Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя | Manualshive

Страница: 22 / 68

background image

54D0700

BDV Series Gas Fireplace

VENt INStALLAtION

BELOW GRADE INStALLAtIONS

When it is not possible to meet the required vent terminal clearances of 12" above grade level, a

snorkel kit is recommended. It allows installation depth down to 7" (178 mm) below grade level. The 7"

(178 mm) is measured from the center of the horizontal vent pipe as it penetrates through the wall.

Ensure that sidewall venting clearances are observed. If venting system is installed below

ground, we recommend a window well with adequate and proper drainage to be installed

around the termination area.

If installing a snorkel, a minimum 24" vertical rise is necessary. The maximum horizontal run with

the 24” vertical pipe is 36". This measurement is taken from the collar of the fireplace (or transition

elbow) to the face of the exterior wall. See the Sidewall Venting Graph for extended horizontal run

if the vertical exceeds 24".
1. Establish vent hole through the wall.

Figure 16, page 18

2. Remove soil to a depth of approximately 16" below base of snorkel. Install drain pipe. Install

window well (not supplied). Refill hole with 12" of coarse gravel leaving a clearance of approxi-

mately 4" below snorkel.

See Figure 26.

3.   Install vent system.
4.   Ensure a watertight seal is made around the vent pipe coming through the wall.
5.   Apply high temperature sealant caulking (supplied) around the 4" and 7" snorkel collars.
6.   Slide the snorkel into the vent pipes and secure to the wall.
7.   Level the soil so as to maintain a 4" clearance below snorkel.

Figure 26

FP1965
below grade install

FP1965

Figure 26 - Below Grade Installation

Screws

Minimum

4" Clearance

Ground

Window Well

Gravel

Drain

Foundation Wall

Firestop

24"

Minimum

FP1966
snorkel

FP1966

Figure 27 - Snorkel Installation,

Recessed Foundation

Foundation

Recess

Watertight Seal

Around Pipe

Sheet Metal

Screws

Wall Screws

Snorkel

• Do not back fill around snorkel.
• A clearance of at least 4" must be

maintained between the snorkel and

the soil.

W

ARNING

If the foundation is recessed, use recess brackets (not supplied) for securing lower portion of the

snorkel. Fasten brackets to wall first, then secure to snorkel with self drilling #8 x 1/2 sheet metal

screws. It will be necessary to extend vent pipes out as far as the protruding wall face.

Figure 27

«
...
20
21
22
23
24
...
»

Содержание Direct Vent Gas Fireplace BDV300





































































Отзывы:

Нет отзывов

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренд: JAYLINE Страницы: 15

Бренд: Valor Страницы: 41

Бренд: Archgard Страницы: 64

Бренд: Amantii Страницы: 21

UNI G CHIMNEY 06

Бренд: UNIPRODO Страницы: 11

Бренд: Varde Страницы: 44

Бренд: Valor Страницы: 46

Бренд: Valor Страницы: 6

Бренд: ORTAL Страницы: 17

Бренд: Riello Страницы: 48

Бренд: Cal Flame Страницы: 32

Edge HCLC/P/L1100

Бренд: Horizon Fireplaces Страницы: 22

Бренд: Regency Fireplace Products Страницы: 44

Patio Lights 23170

Бренд: Landmann Страницы: 4

Бренд: Somogyi Страницы: 18

Бренд: Valor Страницы: 28

Бренд: Glen Dimplex Страницы: 5

Бренд: Astria Fireplaces Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды