Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 14 / 68

54D0700

FP1991
remove screws

FP1993
replace flue pipe

FP1992
remove flue pipe

BDV Series Gas Fireplace

VENt INStALLAtION

OptIONAL tOp VENt AppLIcAtION

The appliance is shipped as a rear vent unit. If the instal-

lation layout requires the unit to be a top vent configu-

ration the appliance can be converted by following the

steps below.
When removing and refitting the plates and adapter be

sure the associated gaskets are undamaged and refitted

as required.
1. Remove the eight (8) screws securing the flue pipe

adapter to the fireplace body.

Figure 8

2. Set the flue pipe adapter aside, complete with the

gasket. Do not damage the gaskets as the adapter

and gasket must be refitted.

3. Remove the eight (8) screws securing the flue pipe

cover to the top of the intake box and remove the

cover and gasket.

Figure 8

4. Remove the six (6) screws securing the flue pipe to

the back of the intake box and remove the pipe and

gasket.

Figure 9

5. Replace flue pipe to top of firebox. Ensure the gasket

is in place and undamaged. Secure with six (6)

screws.

Figure 10

6. Place the flue pipe cover and gasket removed in Step

3 over the flue opening in back of the intake box.

7. Refit the flue pipe adapter and gasket to the top of

fireplace. Secure the adapter with eight (8) screws

removed in step 1.

After conversion to top vent

configuration the 4" (100mm) flue pipe

should be concentric within the 6

(175mm) outer collar (within

").

ARNING

Figure 8 - Removing sixteen (16) Screws from Flue

Pipe Adapter and Flue Pipe Cover

Figure 9 - Removing Flue Pipe

Figure 10 - Attaching Flue Pipe to Top

Vent Configurations

Screws

Flue Pipe

Cover

Flue Pipe

Adapter

Flue Pipe

Screws

Flue Cover

Flue Pipe

Screws

FP1991

FP1992

FP1993

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды