Monessen Hearth Direct Vent Gas Fireplace BDV300 страница 29 Скачать руководство пользователя

Страница: 29 / 68

54D0700

BDV Series Gas Fireplace

FIREpLAcE INStALLAtION

A listed manual shutoff valve must be installed upstream of the appliance. Union tee and plugged

" NPT pres-

sure tapping point should be installed upstream of the appliance.

Figure 40

IMPORTANT:

Install main gas valve (equipment shutoff valve) in an accessible location. The main gas valve is

for turning on or shutting off the gas to the fireplace.

Check your building codes for any special requirements

for locating equipment shutoff valve to fireplaces.
Apply pipe joint sealant lightly to male threads. This will

prevent excess sealant from going into pipe. Excess

sealant in pipe could result in clogged burner system

valves.

A manual shutoff valve must be

installed upstream of the appliance.

Union tee and plugged 1/8" NPT

pressure tapping point should be

installed upstream of the appliance.

Figure 40

ION

Use pipe joint sealant that is resistant

to liquid petroleum (lP) gas.

ION

We recommend that you install a sediment trap/drip leg in supply line as shown in

Figure 40

. Locate sediment

trap/drip leg where it is within reach for cleaning. Install in piping system between fuel supply and burner system.

Locate sediment trap/drip leg where trapped matter is not likely to freeze. A sediment trap collects moisture and

contaminants and keeps them from going into the burner system gas controls. If sediment trap/drip leg is not

installed or is installed wrong, burner system may not run properly.

3" Minimum

FP1978
gas connection

Pipe Nipple

Cap

Figure 40 - Gas Connection

Tee Joint

Approved Flexible

Gas Line

CSA Design-Certified Equipment Shutoff Valve

with 1/8" NPT Tap*

Sediment Trap/Drip Leg

Natural Gas

From Gas Meter

(4.5" W.C. to 10.5" W.C. Pressure)

Propane/lP

From External Regulator

(11" W.C. to 13" W.C. Pressure)

NOTE : The gas line connection may be made using 1/2" rigid tubing or an approved flex connector.

Since some municipalities have additional local codes it is always best to consult your local authorities

and the current edition of the National Fuel Gas Code ANSI.Z223.1, NFPA54. In Canada CSA B149 (1 or

2) Installation Code.

Only persons licensed to work with

gas piping may make the necessary

gas connections to this appliance.

ARNING

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды