Monessen Hearth Direct Vent Gas Fireplace BDV300 страница 28 Скачать руководство пользователя

Страница: 28 / 68

54D0700

FP1977
external regulator

Figure 39 - External Regulator with Vent Pointing Down

(Propane/LP Only)

Use only new black iron or steel pipe.

Internally tinned copper or copper

tubing can be used per National Fuel

code, section 2.6.3, providing gas

meets hydrogen sulfide limits, and

where permitted by local codes. Gas

piping system must be sized to provide

minimum inlet pressure (listed on

data plate) at the maximum flow rate

(BTU/hr). Undue pressure loss will

occur if the pipe is too small.

ION

FP1977

BDV Series Gas Fireplace

FIREpLAcE INStALLAtION

chEcK GAS typE

Use proper gas type for the fireplace you are installing. If you have conflicting gas type, do not install fireplace.

See dealer where you purchased the fireplace for proper fireplace for your gas type or conversion kit.

INSTAllING GAS PIPING TO FIREPlACE / BURNER SYSTEM lOCATION

For propane/lP units, never connect fireplace directly to the propane/lP supply. This

burner system requires an external regulator (not supplied). Install the external regulator

between the burner system and propane/lP supply.

ION

A qualified installer or service person

must connect appliance to gas supply.

Follow all local codes.

ARNING

INStALLAtION ItEMS NEEDED

Before installing fireplace and burner system, make sure you have the items listed below.
• External regulator (supplied by installer) •

Piping (check local codes) •

Sealant (resistant to propane/LP gas) • Equipment shutoff valve*

• Test gauge connection* •

Sediment trap (recommended)

• Tee joint

• Pipe wrench

• approved flexible gas line with gas connector (if allowed by local codes — not provided)
* A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge

connection. Purchase the CSA design-certified equipment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply an external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas pressure to between 11 and 13 inches of water. If you do

not reduce incoming gas pressure, burner system regulator damage could occur. Install external regulator with

the vent pointing down as shown in

Figure 39.

Pointing the vent down protects it from freezing rain or sleet.

External

Regulator

100 lb. (min)

Propane/LP

Supply Tank

Vent Pointing

Down

When using copper of flex connectors use only fittings

approved for gas connections. The gas control inlet is

3/8" NPT.

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды