Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 30 / 68

54D0700

BDV Series Gas Fireplace

MILLIVOLt & ELEctRONIc - chEcK GAS pRESSuRE and ELEctRIcAL INStALLAtION

1. Check gas type. The gas supply must be the same

as stated on the appliance’s rating decal. If the

gas supply is different from the fireplace,

StOp!

Do not install the appliance. Contact your dealer

immediately.

2. To ease installation, a 30" (762 mm) flex line with

manual shut-off valve has been provided with on

this appliance. Install and attach 1/2" gas line onto

shut-off valve.

3. After completing gas line connection, purge air

from gas line and test all gas joints from the gas

meter to the fireplace for leaks. Use a solution of

50/40 water and soap or a gas sniffer.

4. To adjust flame height, turn HI/LO knob to HI to

get maximum pressure to burner. Turn HI/LO knob

to LO to get minimum pressure.

5. To check gas pressures at valve, turn captured

screw counter clockwise 2 or 3 turns and then

place tubing to pressure gauge over test point.

Turn unit to high.

Figure 41.

After taking pressure

reading, be sure and turn captured screw clock-

wise firmly to reseal. Do not over torque. Check

test points for gas leaks.

Do not use open flame to check for

gas leaks.

ARNING

FP1979
Millivolt gas valve

FP1979

Figure 41 - Gas Pressure Check at Gas Valve

Pressure

Test “IN”

Pressure

Test “OUT”

HI/LO Knob

Pilot Adjustment Screw

ElECTRICAl WIRING (

Millivolt)

Electrical connections should only be performed by a qualified, licensed electrician.

Main power must be off when connecting to main electrical power supply or performing

service. All wiring shall be in compliance with all local, city, and state codes. The

appliance, when installed, must be electrically grounded in accordance with local codes,

or in the absence of local codes, with the

National Electrical Code ANSI/ NFPA 70 (latest

edition)

and

Canadian Electrical Code, CSA C22.1.

ARNING

label all wires before disconnecting when servicing controls. Wiring errors can cause

improper and dangerous operation.

ION

Verify proper operation after servicing.

This fireplace will work without any electrical supply. Electricity is only needed to operate blower.

NOTE: If installed in mobile home, fireplace must be bolted securely to floor.

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды