Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя | Manualshive

Страница: 12 / 68

background image

1

54D0700

BDV Series Gas Fireplace

Read all instructions completely and thoroughly before attempting installation. Failure

to do so could result in serious injury, property damage or loss of life. Operation of

improperly installed and maintained venting system could result in serious injury,

property damage or loss of life.

W

ARNING

Failure to follow these instructions will

void the warranty.

NO

tI

c

E

INStALLAtION pREcAutIONS

Consult local building codes before beginning the installation. The installer must make sure to select

the proper vent system for installation. Before installing vent kit, the installer must read this fireplace

manual and vent kit instructions.
Only a qualified installer/service person should install venting system. The installer must follow these

safety rules:
  •  Wear gloves and safety glasses for protection.
  •  Use extreme caution when using ladders or when on rooftops.
  •  Be aware of electrical wiring locations in walls and ceilings.
The following actions will void the warranty on your venting system:
  •  Installation of any damaged venting component.
  •  Unauthorized modification of the venting system.
  •  Installation of any component part not manufactured or approved by MHSC.
  •  Installation other than permitted by these instructions.

FINIShING MAtERIAL

NOTE: Any remote wiring (i.e. remote control, wall switch, and optional fan) must be done

prior to final finishing to avoid costly reconstruction.

INStALLAtION INFORMAtION

Only noncombustible materials (i.e. brick, tile, slate, steel, or other materials with a UL fire rating

of Zero) may be used to cover the black surface of the appliance. A 300°F minimum adhesive may

be used to attach facing materials to the black surface. If joints between the finished wall and the

fireplace surround are sealed, a 300°F minimum sealant material (General Electric RTV103 or

equivalent) must be used.

Never obstruct or modify the air inlet or outlet grills (louvers). This may create a

fire hazard.

W

ARNING

VENt INStALLAtION

«
...
10
11
12
13
14
...
»

Содержание Direct Vent Gas Fireplace BDV300





































































Отзывы:

Нет отзывов

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренд: Quadra-Fire Страницы: 36

Бренд: GDC Страницы: 5

luna diamond 550 v

Бренд: M Design Страницы: 27

Бренд: Sherwood Страницы: 8

Бренд: Paramount Fitness Страницы: 14

Simplifyre SFE-ST

Бренд: Hearth and Home Technologies Страницы: 8

Бренд: BIGHORN Страницы: 18

Бренд: Majestic fireplaces Страницы: 24

Бренд: HASE Страницы: 48

Бренд: wiking Страницы: 4

Бренд: Ningbo Страницы: 20

Бренд: SimpliFire Страницы: 2

Бренд: iFire Страницы: 12

Бренд: tepro Страницы: 19

Бренд: Monessen Hearth Страницы: 32

Legend G3 742CFB

Бренд: Valor Страницы: 4

Бренд: Kennedy Страницы: 24

Бренд: Jøtul Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды