Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 18 / 68

54D0700

FP1953
rigid pipe

DVR584-600

Rear vent no elbows

2/99 djt

Top View Flat

Installation

Maximum

20"

FP1954
wall framing

(241 mm)

(92 mm)

(190 mm)

FP1954

BDV Series Gas Fireplace

REAR (THROUGH THE WAll) APPlICATIONS

When installed as a rear vent unit this appliance may be vented directly to a termination

located on the rear wall behind the appliance

• The maximum horizontal distance between the rear of the appliance and the outside of

termination is 20" (508 m).

Figure 14

• Only one 45° elbow is allowed in these installations.

VENtING INStALLAtION

Sealant is not required to assemble BDV/DVB

fireplace venting. Do not use silicone sealant

at the flue exhaust connections.
1. Find the pipe section’s direction label. The

label arrow shall be pointed away from

the firebox and toward the termination.

Firmly insert the initial rigid section/elbow

into the firebox outer collar. Simpson “GS”

and Selkirk “DT” outer walls are hemmed

and will snap into the collar’s tabs. Attach

Simpson’s DirectVent Pro by fully insert-

ing into the collar and securing with self

tapping screws. The screws shall only

penetrate the flue outer wall.

Refer to vent manufacturer’s installation

instructions to properly assemble flue.

2. Locate and cut the vent opening in the wall.

For combustible walls first frame in

opening.

Combustible Interior Walls:

Cut a 11

⁄

x 9

⁄

" W hole through the interior wall.

Combustible Exterior Walls:

Cut a 9

⁄

x 9

⁄

"W square hole through the exterior

wall frame.

Figure 16

Noncombustible Walls:

Hole opening

should be 7

⁄

" (190mm) in diameter.

3. The center of the hole should line up with

the center line of the horizontal rigid vent

pipe end. Pipe shall always run level or

uphill on horizontal runs. Never run pipe

down hill.

Figure 16

Figure 14 - Rear Vent Application,

Maximum Horizontal Distance

Figure 16 - Exterior Wall Framing Dimensions

Note: Horizontal runs of vent

must be supported every three

feet (914mm). Use wall straps

for this purpose.

Figure 15 - Rigid Vent Pipe Connections

Female

Locking Lugs

Male Slots

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды