Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 27 / 68

54D0700

BDV Series Gas Fireplace

FLEx VENt INStALLAtION

C. Routing UL1777 flex pipe.

1. Always maintain the required clearance when routing the flex vent assembly.

2. Install firestop spacers (

Figure 36

) when penetrating ceiling, attic spaces, or walls.

3. Do not allow the flexible vent to bend in radius tighter than 5" (127 mm).

Figure 35

4. Horizontal runs of flexible vent shall be supported at maximum 2 foot intervals; vertical runs, five feet

intervals. Metal strapping, properly secured, is an acceptable means to support the flexible vent.

5. Flexible vent spacers are to be installed at intervals prescribed by the flexible vent manufacturer; and in such

a way as to maintain concentric inner and outer vent spacing.
D. Attaching flexible venting to vertical termination assemblies.

1. When using Simpson pipe, an MHSC flex-to-pipe adapter and/or rigid pipe section(s) is required to con-

nect the flexible vent assembly to the vertical termination by using three self-penetrating screws.

2. Review

Figure 37

and corresponding instructions for proper overlap, clamp and screw placement.

3. Three each self-penetrating screws are drilled opposite one another and below the gear clamp.

4. Use only listed and approved terminations and accessories, installed per the installation instructions and

Figure 36

E. Installing flexible venting to horizontal termination assemblies.

1. Connect the 4" flexible vent to the horizontal termination.

Figure 38

2. Slide termination cap adapter ring over the termination cap's outside pipe and secure with three

screws.

3. Connect the 7" flexible vent to the termination adapter ring.

Figure 38

4. Review

Figure 38

for proper overlap and clamp placement.

5. Three each self-penetrating screws are drilled opposite one another and below the gear lamp.

6. Use only listed an approved terminations and accessories, installed per the termination instructions and

Figure 38

Termination

Cap

Storm Collar

Roof Sup-

port

Flashing

Rigid Pipe

Length

Flex to Pipe

Adapter

(FPA/8)

Firestop

UL1777 Flex

PIpe

DVFA/8

Adapter

Figure 36 - Typical Vertical Flex Vent

Installation

FP1974

FP1975
pipe connection

Screws

(3 Places

equidistant

just above

gear clamp)

Rigid Pipe Length

Flex to Pipe Adapter

(FPA/8)

Gear Clamp

" Flexible Pipe and

Adapter Outer Collar Over-

lap

UL1777 Flex Vent

Figure 37 - Typical Pipe Connection

Gear Clamp

FP1975

FP2099
horiz flex vent

Screws

(3 Places equidistant

just above gear clamp)

Gear Clamp

UL1777 Flex Vent

" Flexible Pipe and Adapt-

er Outer Collar Overlap

MHSC Horizontal

Vent Termination

Termination to

Flex Adapter

(FPA/8)

Figure 38 - Typical Horizontal Flex Vent Installation

FP2099

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды