Before using the washer for the first time, wipe the inside and outside with
a damp cloth to remove any travel dust that has accumulated. We recommend
operating a rinse cycle to rinse out your washer. Front load horizontal axis
washing machines require less detergent. Soap suds line should not exceed the
halfway point of the glass door.
To begin a wash load:
• Sort and pre-treat clothes.
• Add the measured amount of detergent suggested by the package
directions (maximum two tablespoons).
• Load the clothes loosely into the washer. Close the washer door.
• Turn the cycle selector knob to the desired temperature setting.
• Decide which washing cycle you wish to use. Turn the timer knob
clockwise to the desired wash setting.
• Select High or Medium spin (only for regular washing).
• Press the push button
ON
.
• After the cycle is complete, wait two minutes for the door lock to release
before attempting to open the door.
WARNING: Do not wash or dry articles that have previously
been cleaned, washed, soaked, or spotted with gasoline, dry
cleaning solvents or other flammable or explosive substances.
They give off vapors that could ignite or explode. Do not add
gasoline, dry cleaning solvents or other flammable or
explosive substances to the wash water. Do not use heat to dry
articles containing foam rubber or similar textured, rubber-
like materials. Clean the lint screen, if applicable, (located on
the back of the washer in the top left corner) after each use.
Keep the area around the exhaust opening and adjacent areas
free from the accumulation of lint, dust and dirt.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
The removable drain screen which protects the pump
from lint and foreign matter needs to be cleaned periodically.
How often will depend on the type of clothes that you wash.
Cotton articles cause more lint to collect than nylon articles.
Under no circumstance should the drain screen be removed
while the machine is full of water. To clean the drain screen,
open the service door by pressing on the left hand side.
Place a cloth or shallow tray under the drain screen housing,
as a small quantity of water may run out. You may find it
helpful to first set the machine to spin then remove the drain
screen. This procedure reduces the amount of water released.
Turn the drain screen counterclockwise and pull the drain
screen out. Clean the screen to remove any dirt and lint. To
replace the screen, slide it back into the housing and turn it
clockwise to secure. Close the service door.
Appliance & Equipment
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
E X E C U T I V E
3 • 8 2
Operating
Instructions
Cleaning the Drain Screen
Содержание Executive 2001
