Mitsubishi Electric FR-D710W-0.1K, Инструкция по эксплуатации

Страница: 129 / 313

127
Function assignment of external terminal and control
4
P
ARAM
ETE
R
S
4.10.8 Remote output selection (REM signal, Pr. 495, Pr. 496)
You can utilize the ON/OFF of the inverter's output signals instead of the remote output terminal of the programmable
logic controller.
Parameter
Number
Name
Initial
Value Setting
Range
Description
495
Remote output
selection
0
0 Remote output data clear at powering OFF Remote output data is
cleared during an
inverter reset
1
Remote output data retention at powering
OFF
10 Remote output data clear at powering OFF Remote output data is
retained during an
inverter reset
11
Remote output data retention at powering
OFF
496
∗
Remote output data 1
0 0 to 4095 Refer to the following diagram.
The above parameters can be set when
Pr. 160 Extended function display selection
= "0".
(Refer to page 163)
∗
This parameter allows its setting to be changed during operation in any operation mode even if "0" (initial value) is set in Pr. 77 Parameter write selection .
<
Remote output data
>
Pr. 496
The output terminal can be turned ON/OFF depending on
the
Pr. 496
setting. The remote output selection can be
controlled ON/OFF by computer link communication from
the PU connector.
Set "96 (positive logic) or 196 (negative logic)" to
Pr.190,
Pr.192 or Pr.197 (output terminal function selection)
, and
assign the remote output (REM) signal to the terminal
used for remote output.
When you refer to the diagram on the left and set 1 to the
terminal bit (terminal where the REM signal has been
assigned) of
Pr. 496 , the output terminal turns ON (OFF
for negative logic). By setting 0, the output terminal turns
OFF (ON for negative logic).
b11 b0
∗ ∗ ∗ ∗
SO
∗
AB
C
∗ ∗ ∗ ∗
RUN
∗
Any
...
Specifications differ according to the date assembled. Refer to page
298 to check the SERIAL number.
Example: When "96 (positive logic)" is set in Pr. 190 RUN terminal function selection and "1" (H01) is set in Pr. 496 , the
terminal RUN turns ON.
ON/OFF example for positive logic
Signal condition during a reset
∗
When Pr. 495 = "1," the signal condition saved in EEPROM (condition of the
last power OFF) is applied.
When Pr. 495 = "0 (initial value), 10", performing a power ON
reset (including a power failure) clears the REM signal
output. (The ON/OFF status of the terminals are as set in
Pr.
190, Pr. 192, Pr.197 ) The Pr. 496 setting becomes also "0".
When Pr. 495 = "1, 11", the remote output data before power
OFF is stored into the EEPROM, so the signal output at
power recovery is the same as before power OFF. However,
it is not stored when the inverter is reset (terminal reset,
reset request through communication).
(See the chart on the left.)
When
Pr. 495 = "10 or 11," the signal before the reset is held
even during an inverter reset.
REMARKS
The output terminal where the REM signal is not assigned using Pr.190, Pr.192 or Pr.197 does not turn ON/OFF if 0/1 is set to the
terminal bit of Pr. 496 or Pr. 497 . (It turns ON/OFF with the assigned function.)
Parameters referred to
Pr. 190, Pr. 192, Pr. 197 (output terminal function selection) Refer to page 120
Power
supply
OFF OFF
ON OFF REM REM
REM signal clear
REM signal held
REM signal is saved
Inverter
reset time
(about 1s)
Pr. 495 = 0, 10 Pr. 495 = 1, 11
Power
supply
Reset ON
ON OFF ON REM REM
Pr. 495 = 0, 1 Pr. 495 = 10, 11
Reset ON
∗