Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 57 / 63

5.0 Operation

5.3.3.3 Internal Fault Messages -

The inverter continually monitors several internal components. If an condition

inside the inverter occurs that does not allow proper operation, the inverter

will shut down to help protect itself. To clear these “internal” type of faults,

the inverter will require an inverter reset.

Remedy:

Perform an inverter reset; see section 6-2. After resetting

the inverter, press the ON/OFF INVERTER button to turn the inverter

on and verify the fault has cleared. If the “internal” fault remains, the

inverter will require repair at an authorized service facility.

Internal Bridge

– This fault message displays and the inverter shuts down

because the internal power-bridge protection circuit has been activated.

Internal Charger

- This fault message displays and the inverter shuts

down because the internal charger protection circuit has been activated.

Internal NTC

- This fault message displays and the inverter shuts down

because the internal NTC (temperature sensor) circuit has been activated.

Internal Relay

- This fault message displays and the inverter shuts

down because the internal AC transfer relay protection circuit has been

activated.

•

Internal Charger

appears on the

LCD and the FAULT (red) LED is on.

The PWR (green), CHG (green) and

INV (green) LED’s are off.

FAULT

PWR

CHG

INV

Internal Charger

Settings/Info...

Figure 5-34, Internal Charger Fault

Internal Bridge

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

Internal Bridge

Settings/Info...

Figure 5-33, Internal Bridge Fault

Internal NTC

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

Internal NTC

Settings/Info...

Figure 5-35, Internal NTC Fault

Internal Relay

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

Internal Relay

Settings/Info...

Figure 5-36, Internal Relay Fault

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды