Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 9 / 63

3.0 Setup

When the remote is connected to a Magnum inverter/charger, the settings in

the remote control determine the inverter/charger operating parameters. The

default settings in the remote control (see Table 3-4, Inverter/Charger Default

Settings) are adequate for most installations, however you have the option to

change some of the operating parameters if required. This section will show

you how to navigate the remote, give you an understanding of the function of

each adjustable setting, and help you decide what setting should be used.

3.1 Navigating the Remote’s Menu

The ME-ARC has an internal structure that provides menu items and adjust-

able settings that provide the ability to con

gure your inverter/charger to

your speci

c parameters.

Info:

See Figure

4-1, Inverter/Charger Menu Map

for a complete

map of the inverter/charger menu items and adjustable settings.

Familiarize yourself with the items on the front panel which are used to

nd,

adjust and save the desired setting. They are:
•

LCD Display -

The bottom line of the LCD display shows the menu items,

adjustable settings, or the meters display information.

Info:

The bottom line of the LCD display returns to the Home Screen

to show DC voltage and current (see

Figure 3-1

) after 5 minutes - if

no buttons have been pressed.

Info:

When the

”

←

”

(left facing arrow) symbol is shown on the

display it indicates that the displayed setting has been selected and

will be used.

•

Menu Pushbuttons (x5) -

These

ve buttons allow simple access to the

menu items that can help with con

guring, monitoring and troubleshooting

your inverter/charger system.

•

Rotary SELECT Knob -

This knob allows you to quickly scroll through

and select various menu items and settings. Pushing on the knob selects the

menu item to change or saves this current selection. Refresh the LCD display

by holding this knob down for 7 seconds.

Inverting

DC 12.6V 56A

Rotary

SELECT Knob

LCD

Display

Pushbuttons

Figure 3-1, Front Panel Set-up Features

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды