Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 19 / 63

3.0 Setup

Fault Amp:

The generator failed to start in the “Start Amps” mode.

Fault Exercise:

The generator failed to start in the “Start Exercise”

mode.

Fault MaxRn:

The generator exceeded Max Run Time and has turned

off.

Info:

The generator will shut down when reaching the Max Run Time

and may still be running if this fault is observed.

Gen Run Fault:

The generator successfully started and ran fro more

than 5 minutes, but unexpectedly stopped before the ME-AGS-N could

automatically stop the generator.

Fault SOC:

The generator failed to start in the “Start SOC” mode.

Fault Temp:

The generator failed to start in the “Start Temp” mode.

Fault Test:

The generator failed to start in the “test” mode.

Fault Time:

The generator failed to start in the “Start Time” mode.

Fault Topoff:

The generator failed to start in the “Start Topoff” mode.

Fault VDC:

The generator failed to start in the “Start VDC” mode.

•
•

•

•
•
•
•
•
•

Manual Run:

The generator has be started manually either from the

“03 Gen Control” menu or from a start/stop switch directly connected

to the generator.

No Comm:

The ME-AGS-N is not communicating with the ME-ARC re-

mote. Causes could be a bad ME-AGS-N network cable, no power to the

ME-AGS-N, or there is no ME-AGS-N installed in the system.

Off:

Generator is off and the AGS will not auto start the generator.

Quiet Time:

The ME-AGS-N has entered Quiet Time as set in menu “04G

Quiet Time”. The generator will not auto start during Quiet Time.

Ready:

03 Gen Control is set to Multi, and the ME-AGS-N is ready to

automatically start the generator based on the 04 AGS Setup settings.

Start Amp:

The generator has started based on the settings in menu

“04C Gen Run Amps”.

Start Exercise:

The generator has started based on the settings in menu

“04H Gen Exercise”.

Start SOC:

The generator has started based on the settings in menu

“04D Gen Run SOC”.

Start Temp:

The generator has started based on the settings in menu

“04E Gen Run Temp”.

Start Test:

The ME-AGS-N is in the test mode. The test mode may be

started from the test button located on the ME-AGS-N (see the manual

for the ME-AGS-N for further information on the test button).

Start Time:

The generator has started based on the settings in menu

“04B Gen Run Time”.

Start Topoff:

The generator has started based on the settings in menu

“04G Quiet Time”.

Start VDC:

The generator has started based on the settings in menu

“04A Gen Run VDC”.

•

•
•

•

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды