Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 28 / 63

3.0 Setup

03B Battery Type

- Used to select the battery type, which determines

the battery charge pro

le and ensures the batteries are receiving the proper

charge voltage. The

xed voltage selections are GEL (for Gel batteries),

Flooded (for liquid lead acid batteries), AGM 1 (for Lifeline AGM batteries),

and AGM 2 (for East Penn/Deka/Discover/Trojan AGM batteries).

The

‘Custom’ selection allows the Float and Absorb charge voltage settings to be

individually adjusted. S

ee Table 3-3 to determine the speci

c charge voltage

based on the Battery Type selected.

Default setting:

Battery Type = Flooded

Info:

The voltage settings shown in Table 3-3 are based on the

Battery Temperature Sensor (BTS) having been disconnected or at

a temperature of 77° F (25° C). If the BTS is connected, the actual

charge voltage will increase if the temperature around the BTS is

below 77° F (25° C), and decrease if higher than 77° F (25° C). This

ensures the batteries receive the correct charge voltage regardless

of temperature.

Table 3-3, Battery Type to Charge Voltages

•

Battery

Type

Inverter

Voltage

Absorption

Voltage

Float

Voltage

Equalization

Voltage

GEL

12 VDC

14.1 VDC

13.6 VDC

14.1 VDC

24 VDC

28.2 VDC

27.2 VDC

28.2 VDC

48 VDC

56.4 VDC

54.4 VDC

56.4 VDC

Flooded

12 VDC

14.6 VDC

13.4 VDC

15.5 VDC

24 VDC

29.2 VDC

26.8 VDC

31.0 VDC

48 VDC

58.4 VDC

53.6 VDC

62.0 VDC

AGM 1

12 VDC

14.3 VDC

13.1 VDC

15.5 VDC

24 VDC

28.6 VDC

26.2 VDC

31.0 VDC

48 VDC

57.2 VDC

52.4 VDC

62.0 VDC

AGM 2

12 VDC

14.5 VDC

13.5 VDC

14.5 VDC

24 VDC

29.0 VDC

27.0 VDC

29.0 VDC

48 VDC

58.0 VDC

54.0 VDC

58.0 VDC

Custom

12 VDC

12.0-16.0 VDC 12.0-16.0 VDC

15.0-16.0 VDC

24 VDC

24.0-32.0 VDC 24.0-32.0 VDC

30.0-32.0 VDC

48 VDC

48.0-64.0 VDC 48.0-64.0 VDC

60.0-64.0 VDC

Note 1: voltage same as absorption voltage - to prevent equalization.

Note 2: specifi cations for Concord (Lifeline Series) AGM batteries.

Note 3: specifi cations for East Penn, Deka, Discover and Trojan AGM batteries.

Note 4: requires inverter with enabled software to operate.

03C Max Charge Rate -

Used to set the maximum charge rate allowed

to charge the batteries during bulk, absorption,

oat and equalize charging.

Selections are ‘Max charge = 0%’ up to “Max charge = 100%”. The Max

charge = 0% setting is available to help minimize charging while continuing

to allow pass-thru power. The rest of the selections are provided to limit

the charge rate to the battery bank, which helps prevent battery overheating

caused by charging at too high a charge rate.

•

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды