Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 11 / 63

3.0 Setup

3.2 Pushbuttons and Menu Items

The

ve menu pushbuttons (FAVS, CTRL, METER, SETUP or TECH) allow the

inverter/charger system to be con

gured to your speci

c preferences. These

menus also allow you to access menu items that can help with monitoring

and troubleshooting your system.
Read this section to help understand the function of each Menu button and

the con

gurable settings - to determine if they should be changed to optimize

the operation of the inverter/charger.

3.2.1 FAVS Button

The FAVS button is short for FAVORITES. This button is similar to the Favorites

button on your TV remote, it allows you to store the most frequently used

menu items for quick reference or changes to the system.
This menu button allows 5 menu items to be stored for quick access without

having to

nd them within the SETUP or other control buttons. The 5 menu

items stored under the FAVS button should be the “favorite” menus most

often used.
Before changing the default FAVS menu items it is suggested that you

thoroughly review all the menu items in the menu map on pages 34 thru 37

and make a short list of the items you think you will use most often. Once

you have determined which 5 items you would like to make your favorites,

then decide in what order you would like those menus to appear under the

FAVS button. This is important since you will assign a FAVS position 1-5 for

each menu item you select to be a FAVS.
Menu items can be changed anytime under the FAVS button. Navigate to the

menu item that you would like to set as a favorite, then push and hold the

FAVS button for 3 seconds. After 3 seconds the screen will show “Select FAV:

F1” on the bottom line. Rotate the knob to select FAVS 1 through 5. Once you

have decided which location you would like the menu item to be in, press the

SELECT knob to save the menu item at the selected location.

Info:

The FAVS button can be used to store menu items that would

otherwise not be accessible after a PIN has been set for the SETUP

menu.

Info:

Menu “Headings” cannot be stored in FAVS, only menu

“Items”. Menu headings are identi

ed with a number followed by

the Menu heading. Menu items are identi

ed by a number followed

by a letter.

Status

02 Invert Setup

02A Search Watts

5 Watts

Example:

“02 Invert Setup” is a menu heading

Example:

“02A Search Watts” is a menu item

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды