Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 52 / 63

5.0 Operation

Overtemp

– This fault message indicates the inverter/charger has shut

down because the internal power components (FET’s and/or Transformer)

have exceeded their safe temperature operating range. When the unit has

cooled down, it will automatically restart and continue operation.

Remedy:

If the fault occurs while inverting, reduce the load on the

inverter; if it occurs while charging, turn down the charge rate. If this

fault happens often, ensure the inverter is not in a hot area, has proper

ventilation, and the cooling fans inside the inverter are working.

AC Overload

- This fault message displays when the AC load on the inverter/

charger’s output has exceeded the inverters AC current protection limits. If the

overload condition lasts for less than 10 seconds, the unit will, automatically

restart and resume operation. However, if the overload occurs more than 10

seconds, the unit will shut down and require a manual restart.

Remedy:

This fault usually occurs because the connected AC loads

are larger than inverter’s output capacity, there is a wiring short on

the output or the output, wires are incorrectly wired. Once the AC

loads are reduced, or the output wiring is corrected; the inverter can

be restarted after a manual restart has been accomplished.

•

Overtemp

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

Overtemp

Settings/Info...

Figure 5-18, Overtemp Fault

AC Overload

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

AC Overload

Settings/Info...

Figure 5-19, AC Overload Fault

High Volts AC

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LED’s are off.

FAULT

PWR

CHG

INV

High Volts AC

Settings/Info...

Figure 5-21, High Volts AC Fault

High Volts AC

- This fault causes the AC Input to be disabled because

a very high AC voltage (>150 VAC; or >300 volts for Export inverters) has

been detected on the AC input.

Remedy:

Remove all AC power from the inverter’s AC input for

at least 15 minutes to automatically restart this fault; ensure only

120VAC power is connected to each of the inverter’s AC inputs.

•

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды