Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 42 / 63

5.0 Operation

This section explains how to operate the inverter/charger with the ME-ARC

remote. It also helps to explain the operational status determined by the LED

indicators and LCD display.

5.1 Front Panel

The ME-ARC front panel contains LEDs and a LCD display for viewing system

status; pushbuttons to control system operation; and a rotary knob that

allows an easy way to select and

nd system information.

Inverting

DC 12.6V 50A

Rotary

SELECT Knob

LCD Display

Buttons

ON / OFF

Buttons

LED Indicators

5.1.1 LED Indicators

There are four LED indicators on the front panel that light solid or blink to

indicate the inverter/charger’s status. When the remote is

rst powered-up,

all the LED’s come on as it goes through a self-test. Once the self-test is

complete, the LED’s along with the LCD provide the operating status of the

inverter/charger. See section 5.3.4 for the LED Indicator Guide.

5.1.2 LCD Display

The LCD display is used for setting up the system operation, as well as

viewing the current operating status or any fault condition. This display

has two lines of alphanumeric characters and features a backlight that can

be set to turn off to conserve power. The top line provides the inverter/

charger status, which is detailed in this section. The bottom line displays

battery information while using the METER menu, system troubleshooting

information while in the TECH menu, and menu items that can be con

gured

for your speci

c system operation while in the SETUP menu. This display

automatically powers up with the current system status on the top line and

the Home Screen (detailing the inverter’s DC voltage and current as shown

in Figure 5-1) on the bottom line.

Figure 5-1, ME-ARC Front Panel Controls and Indicators

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды