Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 16 / 63

3.0 Setup

Inverting

01 DC Meters

Rotary

SELECT Knob

LCD

Display

METER

Button

Figure 3-5, Meter Button

AUTO:

This selection uses the settings in “04 AGS Setup” to automatically

start and stop the generator. Refer to menu 04 AGS Setup on page 29 to set

the start and stop parameters for the generator.

ON:

The ON selection will start the generator by sending a “start” command

from the ME-AGS-N control module. Once the generator is started it may

be stopped by selecting OFF from the GEN Control menu, this sends a stop

command from the ME-AGS-N control module.

Info:

You can manually start the generator by selecting ON from the

GEN Control menu, and then change the selection to AUTO to auto-

matically stop the generator. When the AUTO setting is selected after

the generator has been manually started it will use the STOP setting

in menu 04A “Set Stop Gen Volts” or menu 04F “Max Gen Run Time”,

whichever occurs

rst. This setting is useful if you want to make sure

the generator starts before you leave, but also want to make sure

the generator doesn’t run too long, thereby wasting fuel.
The start selection uses warm-up time. The stop selection stops im-

mediately it does not use the cool-down time.

Press to

select m eters

press

METER

rotate to

desired

selection :

Status

01 DC Meters

T op line show s inverter/

charger status

Bottom line show s current

m enu heading

T o select the next

M eter m enu

Status

02 AC Meters

Status

03 AGS Meters

Status

04 BMK Meters

Status

01 DC Meters

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды