Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 56 / 63

5.0 Operation

5.3.3.2 Stacking Fault Messages

–

A fault condition may occur when two Inverters are stacked in series - using

the stacking interface to provide 120/240VAC output - that is not possible

on a single inverter installation. Refer to the following fault messages to help

troubleshoot the Inverters.

StackClock Fault

- 1. There is a stacker cable problem; or, 2. One

inverter is losing synchronization with the other inverter.

Remedy:

1. Ensure you are using a Magnum Stacking Cable (this is

not a telephone/data cable, this is a custom made cable). 2. Inspect

the stacker cable and reconnect at both ends (listen and make sure

you hear an audible “click” from the connectors at both Inverters).

Info:

This fault has been known to occur when a Magnum Energy

accessory is plugged into the Stack Port, but the installation is not

using multiple Inverters in a stacked con

guration. If this occurs,

perform an inverter reset (see section 6.2).

Stack Mode Fault -

This unit has detected a problem with the “other”

stacked inverter, check that unit for a fault condition.

Remedy:

This fault will automatically clear when the fault with the

other inverter is corrected.

StackPhase Fault -

1. The AC input wiring is incorrect; or, 2. One

phase was lost from the AC input source; or, 3. One of the inverter’s internal

transfer relay is bad; or, 4. The inverter’s AC input circuit breaker may be

open.

Remedy:

If this fault doesn’t clear after checking these four recom-

mendations; perform an inverter reset (see section 6.2).

•

Stack Mode Fault

appears on the

LCD and the FAULT (red) LED is on.

The PWR (green), CHG (green) and

INV (green) LED’s are off.

FAULT

PWR

CHG

INV

Stack Mode Fault

Settings/Info...

Figure 5-31, Stack Mode Fault

StackClock Fault

appears on the

LCD and the FAULT (red) LED is on.

The PWR (green), CHG (green) and

INV (green) LED’s are off.

FAULT

PWR

CHG

INV

StackClock Fault

Settings/Info...

Figure 5-30, StackClock Fault

StackPhase Fault

appears on the

LCD and the FAULT (red) LED is on.

The PWR (green), CHG (green) and

INV (green) LED’s are off.

FAULT

PWR

CHG

INV

StackPhase Fault

Settings/Info...

Figure 5-32, StackPhase Fault

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды