Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 58 / 63

5.0 Operation

LED

Status

Meaning

PWR

(green)

OFF

1. Inverter is disabled; 2. Remote’s in Power Save

mode - press any button to activate LED’s; 3. No

power to remote (check remote cable or power

to inverter); or 4. No AC power at the inverter’s

AC output terminals.

AC power is available from inverter, utility or

generator at the inverter’s AC output terminals.

FAULT

(red)

OFF

Normal operation.

A fault condition has been detected, check the

LCD display to

nd and correct the cause.

CHG

(green)

OFF

1. Remote is in Power Save mode - press any

button to activate LED’s; or, 2. Charger off - no

utility or AC generator present.

Bulk, Absorb, Float or Equalize charge mode (see

the LCD display to determine charge status).

BLINKING,

display says

“Charger

Standby”.

The charger is in Charger Standby mode. This

occurs when the ON/OFF CHARGER button is

pressed to disable the charger.

BLINKING,

display says

“Full charge”

or “Silent”.

The charger is in Battery Saver mode. This mode

monitors battery voltage level and only Charges

if the battery voltage decreases to a low level.

Silent mode will automatically start charging

when the ReBulk setting is reached.

BLINKING,

display shows

a charging

status (i.e.,

Bulk, Absorb,

Float).

The charger current is automatically decreased

because: 1. Charger Back-off - the inverter’s

internal temperature is getting hot, current is

decreased to reduce/maintain temperature; or

2. Low AC Input Voltage - the input AC voltage

is <85 VAC, charger is disabled to help stabilize

incoming AC voltage to prevent AC disconnect.

BLINKING,

display does

not show any

charge status.

The inverter is detecting AC voltage (from utility

or an AC generator) on the inverter’s AC input

terminals.

INV

(green)

OFF

1. Inverter is disabled; or, 2. Remote is in Power

Save mode - press any button to activate LED’s

Inverter is enabled - 1. Supplying AC power

on the output; or, 2. In standby (if both INV

and CHG LED’s are on); the inverter will

automatically supply AC power to the loads if

utility or generator power is lost.

BLINKING

Inverter is in Search mode (the AC load is below

the Setup 02A Search Watts setting).

5.3.4 LED Indicator Guide

The remote provides the following LED’s; use them along with the LCD display

to determine the operating status.

Table 5-1, LED Indicator Guide

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды