Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 37 / 63

3.0 Setup

Rotate the Select knob to access “Lock SETUP” and “Change PIN” options.

Unlock SETUP -

When “PIN = 0***” is displayed, enter the correct PIN

number and “SETUP

Unlocked”

will be displayed indicating the SETUP button

is now unlocked. Press the SETUP button to access the SETUP menus.

Lock SETUP -

When “SETUP

Unlocked”

is displayed rotate the Select knob

to “Lock SETUP” and press Select. “SETUP Locked” will be displayed and the

SETUP button is now locked.

Change PIN -

When “SETUP

Unlocked”

is displayed, rotate the Select knob

to “Change PIN”, and then press Select. “PIN = xxxx” (xxxx = the current PIN

number set) will now be display and is ready to accept a new PIN number.

Example -

You have set your PIN number to “PIN = 1000”. When Change PIN

is selected “PIN = 1000” will be displayed. The first digit in this example (the

“1”) will be blinking. Turn the Select knob, change the first digit to the new

PIN number you have selected. Continue to change the remaining 3 digits

until you have selected your new PIN number.

Info:

There are some SETUP menus that may be desirable to ac-

cess without giving access to the PIN number to users. This is made

possible in ME-ARC with the FAVS button. Before setting the PIN

number, enter the desired SETUP menus in the FAVS button. Once

the SETUP menus have been entered in the FAVS button the PIN

number can now be entered and the SETUP button will be locked.

The SETUP menus in FAVS will still be accessible without having to

enter the PIN number. See pages 6-7 for more information on the

FAVS button.

TECH: 06 Ext Control:

External Control is a read only menu. Magnum

Energy has adopted an “open protocol” policy which allows third party

firmware companies to control certain functions of the inverter/charger. This

menu displays if any external software is controlling the remote. This menu

is designed to help Magnum Energy tech support personnel determine if the

inverter/charger is operating normally, or being controlled by a third party.
No Ext Control - This menu means that no third party network device is

controlling the ME-ARC remote.
Yes Ext Control - This menu means that a third party network device is

controlling one of the allowable functions of the ME-ARC remote. The

function(s) that are being controlled by a third party will be displayed as a

number. This number can be used by Magnum Tech Support to determine

what code is controlling the ME-ARC remote.

•

TECH: 07 Load Defaults

- This menu restores all settings on the

inverter/charger and any settings on accessories that are networked. To

restore, press and hold the rotary SELECT knob for 5 seconds. After the

default settings have been restored, the display will show DEFAULTS LOADED.

Refer to the menu map on pages 34-37 for default values.

Info:

For information on the factory default settings for any net-

worked accessory; refer to the owner’s manual for that accessory.

•

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды