Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 21 / 63

3.0 Setup

04B SOC:

This display is the best way to monitor the actual state of

the battery. The read only display shows the State Of charge (SOC) for

the connected battery bank. The SOC represents the condition of the

battery as a percentage of the available capacity left in the battery.

Range is 0% to 100%, where 100% represents a fully charged battery

and 0% means the battery is completely discharged.

04C DC Volts - BMK:

This meter displays the real-time battery voltage

from 07.00 to 70.00 volts (± 0.02 volts).

04D DC Amps - BMK:

This meter displays the real-time charge current

(amps into the battery) or discharge current (amps out of the battery).

Charging is shown as a positive (+) number and discharging is shown

as a negative (-) number. The range is from ±0.1 to 999 amps, with a

1.0% accuracy.

04E AH In/Out:

This meter displays the Ampere-Hours returned to

or removed from the battery. When this value is positive, it represents

amp-hours returned to the battery during any subsequent charging. A

negative value represents amp-hours removed from a full battery. Its

range is ±32768 AH.

O4F Resetable AH:

This meter displays the total amp-hours removed

from the battery since it was last reset. This display can be used as

a battery load indicator; to help determine and monitor the battery

load consumption. Its range is 0 to 65,535.0 amp-hours (0.1 amp hour

resolution).

04G Total AH Out:

Total Amp-Hours Removed; this meter displays

the total amp hours removed from the battery since the Sense Module

was

rst connected. This display can be used as a battery service life

indicator. The value is displayed in 0.1k [or 100 amp-hours (“k” equals

1000)] resolution up to a maximum of 6,553.5k amp-hours (6,553,500

amp-hours). The displayed number resets to 0.0k when the Sense

Module is disconnected from power.

04H Minimum VDC:

This menu displays the lowest battery voltage

since the last reset. The voltage shown on the display is averaged each

second and is helpful when troubleshooting or detecting an over-dis-

charge condition.

04I Maximum VDC:

This menu displays the highest battery voltage

since the last reset. The voltage shown on the display is averaged each

second, this allows you to check your charging system (battery charger,

charge controller, etc.), to ensure the charging voltage has been attained.

This display is also helpful when troubleshooting or detecting if an over-

charge condition has occurred.

•

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды