Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 22 / 63

3.0 Setup

Figure 3-6, Setup Button

Press to

select Setup

m enu

press

SETU P

rotate to

desired

selection :

Status

01 Remote Setup

T op line show s current

Setup m enu

Bottom line show s current

Setup m enu heading

T o select the next

Setup m enu

Status

01 Remote Setup

Status

03 Charger Setup

Status

04 AGS Setup

Status

05 BMK Setup

Status

02 Invert Setup

Pressing the SETUP menu button provides access to the menu items and set-

tings that allow the ME-ARC display, inverter/charger, ME-AGS-N and ME-BMK

to be con

gured. Read each menu item to determine if any setting requires

adjustment to meet your system requirements.

Inverting

01 Remote Setup

Rotary

SELECT Knob

LCD

Display

SETUP

Button

3.2.4 SETUP Button

The

rst screen that may appear when the SETUP button is pushed is a pass-

word screen. If the PIN has been set under the TECH button menu

05 SETUP

PIN,

the

rst screen will be the “Enter Setup PIN =” screen. The proper PIN

will now have to be entered in order to access the SETUP menus. After 5

minutes from the

last button push,

the display will automatically bounce to

the “Home” screen and the PIN will need to be reentered in order to access

the SETUP menus.

Info:

Refer to menu “05 SETUP PIN” under the TECH button to set

or change the PIN number.

Info:

In any SETUP menu that contains a range of settings, if the

rst and last settings are equal (set to the same value), the function

will be disabled, even if selected/enabled from the CTRL menu.

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды